1.5m Micro HDMI to HDMI Cable, Black, for Raspberry Pi 4B - RS6363
1.5m Micro HDMI to HDMI Cable Connect a device with a micro HDMI video output to a monitor or television with a standard HDMI input.
₹208.50 GST added at checkout
SKU RS7121 / RS3144
RP2040 IC Microcontroller to the physical world by allowing it to speak to almost any external device. Low cost helps ease the barrier to entry.
₹82.50
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
Description:
RP2040 IC Microcontroller to the physical world by allowing it to speak to almost any external device. High-performance breezes through integer workloads. Low cost helps ease the barrier to entry.
Raspberry PI RP2040 IC Microcontroller Chip is designed to help you bring every last drop of that power to bear. With six independent banks of RAM and a fully connected switch at the heart of its bus fabric, you can easily arrange for the cores and DMA engines to run in parallel without contention.
RP2040 Chip builds Raspberry Pi’s commitment to inexpensive, efficient computing into a small and powerful 7 mm × 7 mm package, with just two square millimetres of 40 nm silicon.
Initially only available onboard the Raspberry Pi Pico, it is now available to buy as a standalone microprocessor chip for your own home-made RP2040 PCB designs, industrial applications and more.
The RP2040 microcontroller comes in a QFN-56 package. The recommended PCB footprint can be found in the datasheet (or see the image below in the Resources section.
Features:
Dual ARM Cortex-M0+ @ 133MHz
264kB on-chip SRAM in six independent banks
Support for up to 16MB of off-chip Flash memory via dedicated QSPI bus
DMA controller
Fully-connected AHB crossbar
Interpolator and integer divider peripherals
On-chip programmable LDO to generate core voltage
2 on-chip PLLs to generate USB and core clocks
30 GPIO pins, 4 of which can be used as analogue inputs
Peripherals
2 UARTs
2 SPI controllers
2 I2C controllers
16 PWM channels
USB 1.1 controller and PHY, with host and device support
8 PIO state machines
Pin Description:
Number of processor cores (2)
Loosely which type of processor (M0+)
floor(log2(RAM / 16k))
floor(log2(nonvolatile / 16k)) or 0 if no onboard nonvolatile storage
GPIOx: General-purpose digital input and output. RP2040 can connect one of a number of internal peripherals to each GPIO, or control GPIOs directly from software.
GPIOx/ADCy: General-purpose digital input and output, with analogue-to-digital converter function. The RP2040 ADC has an analogue multiplexer which can select any one of these pins, and sample the voltage.
QSPIx: Interface to a SPI, Dual-SPI or Quad-SPI flash device, with execute-in-place support. These pins can also be used as software-controlled GPIOs, if they are not required for flash access.
USB_DM and USB_DP: USB controller, supporting Full Speed device and Full/Low Speed host. A 27Ω series termination resistor is required on each pin, but bus pull-ups and pull-downs are provided internally.
XIN and XOUT: Connect a crystal to RP2040’s crystal oscillator. XIN can also be used as a single-ended CMOS clock input, with XOUT disconnected. The USB bootloader requires a 12MHz crystal or 12MHz clock input. For recommended crystals, see Crystal Oscillator.
RUN: Global asynchronous reset pin. Reset when driven low, run when driven high. If no external reset is required, this pin can be tied directly to IOVDD.
SWCLK and SWDIO: Access to the internal Serial Wire Debug multi-drop bus. Provides debug access to both processors and can be used to download code.
TESTEN: Factory test mode pin. Tie to GND
GND: GND Single external ground connection, bonded to several internal ground pads on the RP2040 die.
IOVDD: Power supply for digital GPIOs, nominal voltage 1.8V to 3.3V
USB_VDD: Power supply for internal USB Full Speed PHY, nominal voltage 3.3V.
ADC_AVDD: Power supply for analogue-to-digital converter, nominal voltage 3.3V.
VREG_VIN: Power input for the internal core voltage regulator, nominal voltage 1.8V to 3.3V.
VREG_VOUT: Power output for the internal core voltage regulator, nominal voltage 1.1V, 100mA max current.
DVDD: Digital core power supply, nominal voltage 1.1V. Can be connected to VREG_VOUT, or to some other board-level power supply.
Useful Links:
RP2040 Technical Documentation
RP2040 Datasheet
Package Included:
1 x Raspberry Pi RP2040 IC Microcontroller Chip
Dual ARM Cortex-M0+ @ 133MHz
264kB on-chip SRAM in six independent banks
Support for up to 16MB of off-chip Flash memory via dedicated QSPI bus
DMA controller
Fully-connected AHB crossbar
Interpolator and integer divider peripherals
On-chip programmable LDO to generate core voltage
2 on-chip PLLs to generate USB and core clocks
30 GPIO pins, 4 of which can be used as analogue inputs
Peripherals
2 UARTs
2 SPI controllers
2 I2C controllers
16 PWM channels
USB 1.1 controller and PHY, with host and device support
8 PIO state machines
More in Raspberry Pi Boards
1.5m Micro HDMI to HDMI Cable Connect a device with a micro HDMI video output to a monitor or television with a standard HDMI input.
₹208.50 GST added at checkout
This thickened thermal conductive silica gel pad is designed to facilitate efficient heat dissipation between integrated circuits (ICs) and heatsinks.
₹52.50 GST added at checkout
The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Each channel of the module can be set up by a high jumper or low-level trigger.
₹547.50 GST added at checkout
Out of stock
1 x 2.4 GHz Wireless USB Controller Compatible with NES/SNES Super Nintendo Classic Games
₹1498.50 GST added at checkout
Check availability