10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT951
Power supply - 9v from 9v battery The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc
₹225.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
KIT INCLUDES:
Breadboard 840 points – 1
9v battery -1
Battery snapper – 1
LED 5mm – 2
Single stand wire 2m - 1
Resistor (10k – 4 , 1m ohm – 2, 330 ohm – 2)
Capacitor ceramic 1nF(102) – 2
Push button - 6
NE555 Timer IC -1
HARDWARE REQUIRED
Breadboard 840 points – 1
9v battery -1
Battery snapper – 1
LED 5mm – 2
Single stand wire 2m - 1
Resistor (10k – 4 , 1m ohm – 2, 330 ohm – 2)
Capacitor ceramic 1nF(102) – 2
Push button - 6
NE555 Timer IC -1
SPECIFICATIONS Power supply - 9v from 9v battery
PIN DESCRIPTION
LED
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
CIRCUIT DESCRIPTION
555 Timer IC is connected to the breadboard.
Pin No. 1 is GND and Pin No. 8 is connected to the positive supply.
Pin No. 2 to connected 100K resistor and resistor 2nd leg connected to the positive supply.
Pin No. 2 to connected 1st Push Button leg 1st & 2nd leg connected to the 2nd Push Button 1st leg and 2nd Push Button 2nd leg is connected to the 3rd Push Button 1st leg and 3rd Push Button 2nd leg is GND.
Pin No. 3 to connected 330 ohm resistor and resistor 2nd leg to connected Led positive leg & led negative leg is GND.
Pin No. 4 to connected 100K resistor and resistor 2nd leg connected to the positive supply, Pin No. 4 to connected ceramic capacitor 1nF(102) and capacitor 2nd leg is GND.
Pin No. 4 to connected 4th Push Button 1st leg and 2nd leg is GND, 4th Push Button 1st leg connected to the 5th Push Button 1st leg and 5th Push Button 2nd leg is GND, 5th Push Button 1st leg connected to the 6th Push Button 1st leg and 6th Push Button 2nd leg is GND.
Pin No. 6 and Pin No. 7 connected to the each other and Pin No. 7 to connected 1M resistor 1st leg & resistor 2nd leg connected to the positive supply.
Pin No. 7 to connected to the ceramic capacitor 1nF(102) and capacitor 2nd led is GND.
Breadboard connection positive to positive and negative to negative.
WORKING we are using six switches ( you can add more) in which 3 are CORRECT SWITCH and 3 are WRONG SWITCHES only right combination of CORRECT SWITCHES unlocks the circuit. In the circuit 555 timer IC is used in bi stable mode , which can be reset or triggered by applying a low input on the corresponding pin. The CORRECT SWITCHES are connected to trigger pin( PIN2) when all the switches are pressed trigger pin receives a low input and the LED glows which means the circuit is unlocked.
| Power supply - 9v from 9v battery |
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout