10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT959
Make your own ticking bomb using 555 Timer IC. The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL
₹330.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
Make your own ticking bomb using 555 Timer IC.
KIT INCLUDES:
555 timer IC - 1
10uf capacitors - 3
47K resistor - 2
8 ohm speaker - 1
Breadboard 840 points - 1
Single stand wire 2m – 1
HARDWARE REQUIRED
555 timer IC - 1
10uf capacitors - 3
47K resistor - 2
8 ohm speaker - 1
Breadboard 840 points - 1
Single stand wire 2m – 1
PIN DESCRIPTION
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
CIRCUIT REQUIRED
pin 1 of 555 Timer IC to negative rail on the breadboard
pin 2 of 555 Timer IC to of 555 Timer IC pin 6 and pin 4 of 555 Timer IC to of 555 Timer IC pin 8
pin 8 of 555 Timer IC to positive rail on the breadboard
47 k resistor to pin 2 and 3 of 555 Timer IC
negative of capacitor 1 connects to negative rail positive to pin 2 of 555 Timer IC
positive of capacitor 2 to pin 3 of 555 Timer IC and negative to positive of the speaker and negative of the speaker to ground
WORKING
Once you connect the battery then the circuit will complete and the speaker starts make the sound.
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout