10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT960
Resistors (10kὨ – 3; 220Ὠ - 2;OR 1KὨ - 2) In this project, we will make a Panic Alarm using 555 Timer IC. This Panic Alarm is used to send an emergency signal just by pushing a
₹600.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
KIT INCLUDES:
Breadboard 840 points -1
NE555 Timer Ic -1
Transistor BC547 – 2
9v Battery -1
battery snapper – 1
Led – 2
Resistors (10kὨ – 3; 220Ὠ - 2;OR 1KὨ - 2)
Ceramic capacitor(0.01uF) – 2
Push button – 2
Buzzer – 1
Introduction In this project, we will make a Panic Alarm using 555 Timer IC. This Panic Alarm is used to send an emergency signal just by pushing a single button. After a few time alarm will be off and if you reset the button alarm will stop. HARDWARE REQUIRED
Breadboard 840 points -1
NE555 Timer Ic -1
Transistor BC547 – 2
9v Battery -1
battery snapper – 1
Led – 2
Resistors (10kὨ – 3; 220Ὠ - 2; OR 1KὨ - 2)
Ceramic capacitor(0.01uF) – 2
Push button – 2
Buzzer – 1
PIN DESCRIPTION
LED
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
TRANSISTOR
CIRCUIT DESCRIPTION
Attach 555 Timer IC with the breadboard.
Connect Pin 1 of IC to the GND rail on Breadboard.
Connect 10K resistor to the pin 3 & 4 to the 555 Timer IC and the other terminal of resistors to the GND rail on breadboard.
Connect both leg of 0.01 µf ceramic capacitor to both 5 and 6 pins of 555 Timer IC.
Connect 7th pin of 555 Timer IC to GND rail and 8th pin to the positive rail on breadboard.
Attach two Tactile switches to the breadboard.
Connect one internally connected side of tactile switch to the GND similarly do for the second switch.
Connect 1st tactile switch to the Pin2 of 555 Timer IC.
Connect 2nd Tactile switch to the pin 4 of 555 Timer IC.
Attach Buzzer on the breadboard.
Attach the led in the same column of the buzzer
Connect the positive terminal of led and buzzer to the positive rail on breadboard.
Attach the BC547 transistor to the breadboard
Connect base (middle) pin of transistor to the 3rd pin of 555 Timer IC via 1Kohm Resistor.
Now connect Negative terminal of Led and buzzer to the Collector pin of BC547 transistor via 1K resistor.
Connect Emitter pin of Transistor to the GND rail on the breadboard.
WORKING
When the SET button is pressed LED gets turned on and buzzer starts beeping, When RESET button is pressed the LED and buzzer goes OFF. When you press the reset button, led and buzzer goes off. This is happened because circuit is in disable mode. Whenever you provide the power supply, circuit will operate in astable mode when IC is enabled d. This IC is in 555 timer IC Is given a high voltage.
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout