10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT949
The pin diagram of LM358 IC comprises of 8 pins, where Pin-1 and pin-8 are o/p of the comparator Pin-2 and pin-6 are inverting i/ps Pin-3 and pin-5 are non inverting i/ps Range of
₹750.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
KIT INCLUDES:
555 Timer IC - 1
LM358 IC - 1
Resistor 47k - 2, 10K-5 , 1M-2
LDR - 2
10K Pot - 2
Transistor BC547 - 2
Push Button - 2
Laser Light - 1
Battery 9V -1
Battery snapper - 1
Breadboard 840 points - 1
Single Stand wire 2m - 1
B-20 Piezo buzzer – 1
HARDWARE REQUIRED
555 Timer IC - 1
LM358 IC - 1
Resistor 47k - 2, 10K-5 , 1M-2
LDR - 2
10K Pot - 2
Transistor BC547 - 2
Push Button - 2
Laser Light - 1
Battery 9V -1
Battery snapper - 1
Breadboard 840 points - 1
Single Stand wire 2m - 1
B-20 Piezo buzzer – 1
SPECIFICATION
LM358 IC
The pin diagram of LM358 IC comprises of 8 pins, where
Pin-1 and pin-8 are o/p of the comparator
Pin-2 and pin-6 are inverting i/ps
Pin-3 and pin-5 are non inverting i/ps
Pin-4 is GND terminal
Pin-8 is VCC+
Specifications:
Range of Single power supply is from 3V to 32V
Range of dual power supplies is from + or -1.5V to + or -16V
The supply current drain is very low, i.e., 500 μA
2mV low i/p offset voltage
Common mode i/p voltage range comprises ground
It consists of two op-amps internally and frequency compensated for unity gain
The large voltage gain is 100 dB
Wide bandwidth is 1MHz
Range of wide power supplies includes single and dual power supplies
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
TRANSISTOR
10K POTENTIOMETER
CIRCUIT DESCRIPTION
10K pot, LM358 IC, 555 Timer IC, Push Button and Transistor BC547 connected to the Breadboard.
10K Pot 1st leg(left) connected to the GND and 2nd leg(right) connected to the positive supply.
10K Middle leg connected to the LM358 IC Pin No. 2.
LM358 IC Pin No. 4 is GND and Pin No. 8 connected to the positive supply.
LM358 IC Pin No. 3 to connected LDR and LDR 2nd leg is GND.
LM358 IC Pin No. 3 to connected 20K(10K+10K) Resistor and Resistor 2nd leg connected to the positive supply.
LM358 IC Pin No. 1 to connected 47K Resistor and Resistor 2nd leg connected to the BC547 Transistor Middle leg.
BC547 Transistor 1st leg(left) is GND and BC547 Transistor 2nd leg(right) to connected 10K Resistor and Resistor 2nd leg connected to the positive supply.
BC547 Transistor 2nd leg(right) connected to the 555 Timer IC Pin No. 2.
555 Timer IC Pin No. 1 & 6 are GND and Pin No. 8 connected to the positive supply.
555 Timer IC Pin No. 3 to connected piezo buzzer positive leg and negative leg is GND.
555 Timer IC Pin No. 4 to connected 1M Resistor and Resistor 2nd leg connected to the positive supply.
555 Timer IC Pin No. 4 to connected Push Button 1st leg and Push Button 2nd leg is GND.
Laser Light positive leg connected to the positive supply and negative leg is GND.
Breadboard connection positive to positive and negative to negative.
WORKING
In this circuit, the LM358 ic is working as a comparator and IC LM555 is wired as a bistable multivibrator. The transistor BC547 is wired as a switch to provide the negative trigger at pin 2 of LM555. The 10K pot is used to adjust the sensitivity of the circuit.
When anyone interrupts the laser beam, the LDR will go to darkness which increases the resistance across LDR, which in turn increases the voltage across it. When the voltage at Non-Inverting terminal (PIN 3) will greater than Inverting terminal (PIN 2) the output of the comparator goes high. Thus the output of the transistor goes low and triggers the 555, which sounds the buzzer
| Range of Single power supply is from 3V to 32V | |
| Range of dual power supplies is from + or -1.5V to + or -16V | |
| The supply current drain is very low, i.e., 500 μA | |
| 2mV low i/p offset voltage | |
| Common mode i/p voltage range comprises ground | |
| It consists of two op-amps internally and frequency compensated for unity gain | |
| The large voltage gain is 100 dB | |
| Wide bandwidth is 1MHz | |
| Range of wide power supplies includes single and dual power supplies |
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout