10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT958
Power supply – 9V( from 9v battery) The Shorter Terminal is negative and the longer Terminal is Positive. The OUT pin goes high and a timing interval starts when this input falls
₹648.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
KIT INCLUDES:
Breadboard 840 points -1
Capacitor 47uf -1
NE555 Timer Ic -1
9v Battery – 1
Battery Snapper – 1
Resistor (22 k ohm , 470 ohm , 1 mohm) – 3 per piece
Led – 3
Single stand wire
HARDWARE REQUIRED
Breadboard 840 points -1
Capacitor 47uf -1
NE555 Timer Ic -1
9v Battery – 1
Battery Snapper – 1
Resistor (22 k ohm , 470 ohm , 1 mohm) – 3 per piece
Led – 3
Single stand wire
SPECIFICATION Power supply – 9V( from 9v battery)
PIN DESCRIPTION CAPACITOR
The Shorter Terminal is negative and the longer Terminal is Positive.
LED
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
CIRCUIT DESCRIPTION
pin 1 of 555Timer IC connect with negative rail
Connect pin 2 and 6 of 555Timer IC
pin 2 of 555Timer IC connect with Positive pin of 47uf cap and the negative pin connected to the negative rail
pin 3 of 555Timer IC connected with led positive through 470ohm resistor and negative pin to negative rail
pin 8 of 555Timer IC connected to pin 7 with the 1M resistor and pin 7 to pin 6 with the 22k resistor
pin 8 of 555Timer IC connected to the positive rail
WORKING
The blinking frequency can be varied, by changing the 10uF capacitor value from 4.7uF to 100uF.
| Power supply – 9V( from 9v battery) |
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout