10 x 15 cm FR4 Copper Clad Plate Laminate Single Side PCB - RS2610
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
SKU KT957
LEDs (red and blue) – 2 piece each LEDs (red and blue) – 2 piece each Power supply – 9V( from 9v battery) The Shorter Terminal is negative and the longer Terminal is Positive.
₹270.00
18% GST added at checkout
In stock
₹150 flat shipping, free over ₹3000
Buying for a school or in bulk? Ask us for institutional pricing. Get a quote
KIT INCLUDES:
NE555 Ic - 1
LEDs (red and blue) – 2 piece each
push buttons - 4
10K ohm Resistor - 3
1K ohm Resistor- 3
100 ohm Resistor - 3
1uF Capacitor -2
0.1uF Capacitors – 3
IN4007 or 1N4148 Diodes – 4
Breadboard 840 points – 1
9v Battery - 1
battery snapper – 1
Single stand wire 2m – 1
HARDWARE REQUIRED
NE555 Ic - 1
LEDs (red and blue) – 2 piece each
push buttons - 4
10K ohm Resistor - 3
1K ohm Resistor- 3
100 ohm Resistor - 3
1uF Capacitor -2
0.1uF Capacitors – 3
IN4007 or 1N4148 Diodes – 4
Breadboard 840 points – 1
9v Battery - 1
battery snapper – 1
Single stand wire 2m – 1
SPECIFICATION Power supply – 9V( from 9v battery)
PIN DESCRIPTION
CAPACITOR
The Shorter Terminal is negative and the longer Terminal is Positive.
LED
555 TIMER IC
Pin
Name
Purpose
1
GND
Ground reference voltage, low level (0 V)
2
TRIG
The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.
3
OUT
This output is driven to approximately 1.7 V below +Vcc, or to GND.
4
RESET
A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.
5
CTRL
Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).
6
THR
The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).
7
DIS
Open collector output which may discharge a capacitor between intervals. In phase with output.
8
Vcc
Positive supply voltage, which is usually between 3 and 15 V depending on the variation.
CIRCUIT DESCRIPTION
Reset button point 1 connects to negative rail and point 2 connects to positive of 1uf capacitor positive and capacitor negative to negative rail.
positive of capacitor 1uf to p1 555ic pin 5 and then pin 5 of 555 timer ic to pin 4 of 555 timer ic
capacitor 1uf positive to positive rail on breadboarD
p1 button point 1 to negative rail through 1k resistor and same point to p2 point 1
p1 button point 2 to 0.01uf capacitor to p1 555ic pin 2 and both pin of this cap connect to positive rail through both 10k resistor
p1 555ic pin 1 to negative rail
p1 555ic pin 3 connect to p2 button point 1 through diode in4007
p1 555ic pin 8 to positive rail and 6 pin to negative rail
pin 5 of p1 555ic to p2 555ic pin 4
p2 button point 2 to cap 0.01uf to pin 1 of p2 555ic
p2 555ic pin 1 to negative rail pin 6 to negative rail and pin 8 to positive rail
pin 3 of p2 555ic connect with p2 point 1 through in4001
p1 555ic pin 3 to p1 led positive pin and negative pin to ground
p2 555ic pin 3 to p2 led positive and negative pin to ground
WORKING
The aim is to press the button earlier than your opponent (w/ 2 players). A third person would be there to reset the switches and to restart the game.
One more use of this is, as a Quiz timer. Whichever competent knows the answer, has to quickly press the buzzer, which will lead to the disability of other buttons. Even if
both the players press the buttons at the same time, this circuit can decide between fractions of milliseconds.
You have to be careful with the circuit, as this one has quite messy connections. Use up the entire breadboard space to make it neater. Finally, power up the circuit and press one of the two buttons, the corresponding LED would light up. You will also notice that pressing the other one would now do nothing. Press the reset button to start the game again.
| Power supply – 9V( from 9v battery) |
More in ICs & Prototyping
This Is A High Quality Single Sided Fr2 / Phenolic General Purpose PCB. It Is Used For Rapid Prototyping Design.
₹120.00 GST added at checkout
The universal PCB board is easy to weld diode, resistor, transistor, capacitor, etc. With referencing letters and numbers printed on the Single side for easy reference of
₹31.50 GST added at checkout
This is a 12" x 12" (30 cm x 30 cm) copper-clad PCB. This copper clad is perfect for hobbyists & electronics engineers who have tried successfully making their own single-sided
₹247.50 GST added at checkout
The 12x18cm Double Sided PCB Board Tinned Through Holes Universal Printed Circuit Proto Board. This means the PCB has copper traces (conductors) on both sides of the board.
₹171.00 GST added at checkout