Wireless remote using 2.4 GHz NRF24L01 Simple tutorial using NRF24L01 and Arduino uno - KT988

SKU KT988

Arduino IDE 1.8.5 (programmable platform for Arduino) NRF24L01+ is a single-chip radio transceiver for the worldwide 2.4-2.5 GHz ISM band.

₹3748.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

9v battery - 1

Battery DC jack –1

Arduino uno with USB cable – 2

NRF24L01 – 2

Push button – 1

Led – 2

Breadboard 170 points – 1

Jumper wires male to female – 40 pieces

Jumper wires male to male – 40 pieces

HARDWARE REQUIRED

9v battery - 1

Battery DC jack –1

Arduino uno with USB cable – 2

NRF24L01 – 2

Push button – 1

Led – 2

Breadboard 170 points – 1

Jumper wires male to female – 40 pieces

Jumper wires male to male – 40 pieces

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download: https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

NRF24L01

NRF24L01+ is a single-chip radio transceiver for the worldwide 2.4-2.5 GHz ISM band. The radio transmitters and receivers include frequency generator, enhanced Shock Burst mode controller, power amplifier, crystal oscillator modulator and demodulator. You can select the output power channel and protocol by setting through the SPI port. The current consumption for the nRF24L01+ is extremely low - under the transmitter mode, when the transmitting power is 0dBm, the current consumption is only 11.3mA; under the receiving mode, it is 13.5mA; under the power down and idle mode, the consumption is even lower. As for application, it's widely used in many devices such as wireless mouse and keyboard, game handle, remote control set, industry sensor,toys, etc. The pin functions of NRF24L01 are as shown:

Pin

Name

Description

1

GND

Ground (0V)

2

VCC

Power Supply (3.3V)

3

CE

Mode Enable Activates RX or TX mode

4

CSN

Chip Select

5

SCK

Serial Clock

6

MOSI

Master Output, Slave Input

7

MISO

Master Input, Slave Output

8

IRQ

Interrupt Request. Under wireless communication, MCU communicates with NRF24L01 by IRQ

The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01 provides a true ULP solution enabling months to years of battery lifetime when running on coin cells or AA/AAA batteries

Voltage: 3-3.6V (recommended 3.3V) V

Maximum output power: +20dBm

Emission mode current(peak): 115mA

Receive Mode Current(peak): 45mA

Power-down mode current: 4.2uA

LED

CIRCUIT CONNECTION TRANSMITTER

RECEIVER Connect the following pins to your Arduino: as shown in figure

Pin 9 - CE

Pin 10 - CS(N)

Pin 11 - MOSI

Pin 12 - MISO

Pin 13 - SCK

3.3v - VCC

GND - GND

On the Receiver Pin 3 - LED

On the Transmitter Pin 7 – Button

Same connection for receiver and transmitter and you can use any Arduino board

CODE

For coding Arduino first we need some library files so follow the steps given below:

Download the ZIP file from this linkhttps://drive.google.com/open?id=1uUkFgECfYC1rVOSlrhtzfWQvA3czysji)

Unpack the ZIP file.

Go to Arduino library folder

And paste both the folders named “nFR24L01" and "RF24" into it.

Now, program the Arduino receiver and transmitter

Code for Receiver https://docs.google.com/document/d/e/2PACX-1vR0D73b8ueoIvT5kW_KPXRxbe7ucVuRYIxtp4IwUJI0T371czOjpVDrQGrxi6MBK2TzrOO-C4kDEDXA/pub

Code for Transmitter

https://docs.google.com/document/d/e/2PACX-1vQqocuiFoUWL_CYWIooYa_Lr0tUlkPO9McfwYJ4m81P867qeQTvTkFWcQ-dIxga9FUHfCZqaNPLlN_o/pub

WORKING

This is the last step after completing the circuit and coding part we can easily test it by switching "ON" and "OFF". When the switch is "ON" on transmitter side connected to pin 7 of Arduino then led glows on the receiver’s side connected to pin 3 of Arduino The video shows the output of this project.

More in Arduino Boards

You might also need