About this product
Description:
RP2040-LCD-1.28 is a low-cost, high-performance MCU board designed by Waveshare. Tiny size with onboard 1.28-inch LCD round display, Li-ion battery recharge manager, 6-axis sensor (3-axis accelerometer and 3-axis gyroscope), and so on, adapting all GPIO and Debug pins, which makes it easy for you to develop and integrate it into products quickly.
Specifications:
Controller: GC9A01A
Communication interface: SPI
Display Panel: IPS
Sensor: QMI8658
Accelerometer: Resolution: 16 bits
Measurement Range (optional): ±2, ±4, ±8, ±16g
Gyroscope: Resolution: 16 bits
Measurement Range (optional): ±16, ±32, ±64, ±128, ±256, ±512, ±1024, ±2048°/sec
Resolution: 240 (H) RGB x 240(V)
Display Size: Φ32.4mm
Pixel Size :0.135 (H) x 0.135 (V) mm
Features:
RP2040 microcontroller chip designed by Raspberry Pi (3B, 3B+, 4B, 5) in the United Kingdom
Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
264KB of SRAM, and 2MB of on-board Flash memory
Type-C connector, keeps it up to date, easier to use
Onboard 1.28-inch 240×240 pixels 65K colorful IPS LCD display for clear color pictures
Lithium battery recharge/discharge header, suitable for mobile devices
All GPIO pins are adapted through 1.27 pitch female headers (There are 30 pins in total, but some pins have been connected to the internal circuit, please refer to the wiki for details when multiplexing)
USB 1.1 with device and host support
Low-power sleep and dormant modes
Drag-and-drop programming using mass storage over USB
2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels
Accurate clock and timer on-chip
Temperature sensor
Accelerated floating-point libraries on-chip
8 × Programmable I/O (PIO) state machines for custom peripheral support
Pin Description:
Product Interface:
USB Type-C connector
USB 1.1 with device and host support
ETA6096
high efficiency Lithium battery recharge manager
Battery Header
MX1.25 header, for 3.7V Lithium battery, allows recharging the battery and powering the board at the same time
QMI8658
IMU, includes a 3-axis gyroscope and a 3-axis accelerometer
1.27mm pitch headers
Adapting all GPIO and Debug pins
W25Q16JVUXIQ
2MB NOR-Flash
RP2040
Dual-core processor, up to 133MHz operating frequency
RESET Button
BOOT Button
press it when resetting to enter download mode
Useful Link:
Waveshare RP2040 MCU Board with 1.28-inch Round LCD
Package Included:
1 x RP2040 MCU Board, With 1.28inch Round LCD
RP2040 microcontroller chip designed by Raspberry Pi (3B, 3B+, 4B, 5) in the United Kingdom
Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
264KB of SRAM, and 2MB of on-board Flash memory
Type-C connector, keeps it up to date, easier to use
Onboard 1.28-inch 240×240 pixels 65K colorful IPS LCD display for clear color pictures
Lithium battery recharge/discharge header, suitable for mobile devices
All GPIO pins are adapted through 1.27 pitch female headers (There are 30 pins in total, but some pins have been connected to the internal circuit, please refer to the wiki for details when multiplexing)
USB 1.1 with device and host support
Low-power sleep and dormant modes
Drag-and-drop programming using mass storage over USB
2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels
Accurate clock and timer on-chip
Temperature sensor
Accelerated floating-point libraries on-chip
8 × Programmable I/O (PIO) state machines for custom peripheral support