About this product
Description:
ESP32-S3 5-inch Touch LCD Display: A versatile development board featuring a 32-bit LX7 Dual-Core processor, supporting both Arduino IDE and ESP-IDF for flexible project development. Choose the best framework based on your needs for seamless integration and efficient design.
Specification:
Basic Parameters
Processor
High-performance Xtensa 32-bit LX7 dual-core processor, up to 240 MHz
Wi-Fi/Bluetooth
Supports 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), onboard antenna
Embedded Memory
512KB SRAM and 384KB ROM
Flash
16MB Flash
PSRAM
8MB PSRAM
Power Supply Range
Type-C 5V / DC 7-36V
Screen Parameters
Resolution
800 × 480
Display Colors
65K colors
Display Interface
RGB
Display Panel
IPS
Viewing Angle
160°
Brightness
550 Cd/m²
Touch Type
Capacitive
Touch Panel
Tempered Glass
Touch Features
Supports I2C interface control for capacitive touch, 5-point touch, and interrupt support
Peripheral Interfaces
Communication Interfaces
CAN, RS485, I2C, USB
Digital Input
5–36V, bidirectional optocoupler isolation, supports dry contact and wet contact (NPN or PNP) switch inputs
Digital Output
5–36 V, optocoupler isolation, output uses a high-current transistor, sink current up to 450 mA
USB
Integrated full-speed USB
Others
Power Consumption
5V 450mA
Product Interface:
Features:
Powered by a high-performance Xtensa 32-bit LX7 dual-core processor, with a main frequency of up to 240 MHz.
Supports 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with an onboard antenna
Built-in 512KB SRAM and 384KB ROM, stacked with 16MB Flash and 8MB PSRAM
Onboard 5-inch wide capacitive touch screen, 800 × 480 resolution, 65K colors
Supports I2C interface control for capacitive touch, with 5-point touch, and supports interrupts
Onboard CAN, RS485, I2C interfaces, TF card slot, and integrated full-speed USB
Supports precise control features like flexible clocking and independent module power supply settings, enabling low-power modes for multiple scenarios
Pin Description:
ESP32-S3-WROOM-1-N16R8
The SoC with WiFi and Bluetooth, up to 240 MHz operating frequency, integrated 8 MB PSRAM and 16MB Flash
TF card slot
USB Type-C port
BOOT button
Press and hold while powering on for program burning
RESET button
Optocoupler isolation
Touch panel connector
5-inch display panel connector
RS485 and CAN terminal resistors selection
close by default
Battery power supply ON/OFF
3.7V single lithium battery GH1.25 header
Status Indicators
DONE: Lithium battery charging completed indicator
CHG: Lithium battery charging indicator
PWR: Power supply indicator
(the CHG will blink and DONE will light on when connecting with a DC power supply, and without a lithium battery connected or when the battery switch is OFF)
7-36V DC power supply terminal
I2C interface terminal
VOUT pin output 5V/3.3V (switching by onboard resistor)
CAN interface terminal
RS485 interface terminal
Digital output
5–36V, open-drain output, output load: 450 mA per channel (MAX)
Input signal common terminal
NC: dry contact passive input
Connect to power supply positive: digital input low active, for NPN wet contact active input, 5V-36V DC
Connect to power supply negative: digital input high active, for PNP dry contact active input, 5V-36V DC
Digital input
5–36V, supports passive/active input (NPN or PNP)
I2C VOUT output selection
for switching output voltage and I/O level of I2C VOUT, 3.3V by default
RTC battery holder
Compatible with CR927 battery
CS8501
Lithium battery recharge manager
PCF85063
RTC chip for providing accurate time control
AP3032KTR-G1
Display backlight boost converter
CH422G
IO expansion chip
SP3485
RS485 transceiver
TJA1051T/3/1J
CAN transceiver
SGM2212-3.3
800mA low-noise LD
Application Scenarios:
Useful Link:
Waveshare ESP32-S3 5-inch Touch Display Development Board
Waveshare ESP32-S3 5-Inch No-Touch Display Development Board
Package Included:
1 x Waveshare ESP32-S3 5-inch Display Development Board
Powered by a high-performance Xtensa 32-bit LX7 dual-core processor, with a main frequency of up to 240 MHz.
Supports 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with an onboard antenna
Built-in 512KB SRAM and 384KB ROM, stacked with 16MB Flash and 8MB PSRAM
Onboard 5-inch wide capacitive touch screen, 800 × 480 resolution, 65K colors
Supports I2C interface control for capacitive touch, with 5-point touch, and supports interrupts
Onboard CAN, RS485, I2C interfaces, TF card slot, and integrated full-speed USB
Supports precise control features like flexible clocking and independent module power supply settings, enabling low-power modes for multiple scenarios