About this product
Description:
This is a low-cost, high-performance MCU development board designed by Waveshare. It supports 2.4 GHz WiFi and BLE 5, integrates high-capacity Flash and PSRAM, and has a 4.3-inch wide capacitive touch LCD screen on board to smoothly run GUI interface programs such as LVGL. It combines a variety of peripheral interfaces (e.g., CAN, I2C, RS485, etc.) to quickly develop applications such as HMIs for ESP32-S3. With a wide range of functions and interfaces, it can meet power consumption requirements in the Internet of Things (IoT), mobile devices, smart homes, and other applications.
Specification:
Display Size: 4.3 inches
Display Type: Capacitive Touch
Interface: CAN, RS485, I2C, TF card slot, Full-speed USB
Item Type: Development Board
Processor: Xtensa 32-bit LX7 dual-core, up to 240MHz
Wireless Functions: 2.4 GHz Wi-Fi (802.11 b/g/n), Bluetooth 5 (LE)
Memory: 512KB SRAM, 384KB ROM, 8MB PSRAM, 8MB Flash
Display Resolution: 800 x 480
Features:
Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
Built in 512KB of SRAM and 384KB ROM, with onboard 8MB PSRAM and 16MB Flash
Onboard 4.3-inch LCD display, 800×480 resolution, 65K color
Supports 5-point capacitive touch control via I2C interface, with interrupt support (for touch version only)
Onboard CAN, RS485, I2C interface, and TF card slot; integrates a full-speed USB port
Supports flexible clock, module power supply independent setting, and other controls to realize low power consumption in different scenarios
Product Interface:
Pin Description:
ESP32-S3N16R8: The SoC with WiFi and Bluetooth, up to 240MHz operating frequency, integrated 8MB PSRAM, and 16MB Flash
SGM2212-3.3: 800mA low-noise LDO
FSUSB42UMX: for USB pins multiplexing
Touch panel connector
USB TO UART Type-C port
USB Type-C port
TJA1051T/3/1J: CAN interface chip
CH422G: IO expansion chip
BOOT button: Press and hold while powering on for program burning
RESET button
MP3302DJ-LF-Z: Screen backlight boost chip
4.3-inch display panel connector
TF card slot
Sensor header
CAN header
I2C header
RS485 header
3.7V single lithium battery PH2.0 header
CAN terminal resistor selection
RS485 terminal resistor selection
CH343P: USB to UART chip
SP3485: RS485 transceiver chip
CS8501: Lithium battery recharge manager
Status Indicators:
PWR: Power supply indicator
CHG: Lithium battery charging indicator
DONE: Lithium battery charging completed indicator
Useful Link:
Waveshare ESP32-S3 4.3-inch Display Development Board
Package Included:
1 x ESP32-S3-Touch-LCD-4.3
2 x HY2.0 2P to 2-pin male cable 10cm
1 x HY2.0 3P to 3-PIN male cable 10cm
1 x HY2.0 4P to 4-PIN male cable 10cm
1 x Standoff pack
Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
Built in 512KB of SRAM and 384KB ROM, with onboard 8MB PSRAM and 16MB Flash
Onboard 4.3-inch LCD display, 800×480 resolution, 65K color
Supports 5-point capacitive touch control via I2C interface, with interrupt support (for touch version only)
Onboard CAN, RS485, I2C interface, and TF card slot; integrates a full-speed USB port
Supports flexible clock, module power supply independent setting, and other controls to realize low power consumption in different scenarios