Waveshare 64×128, General 1.3inch OLED Display Module - RS1679

SKU RS1679

MOSI pin of SPI (Data input) SCLK pin of SPI (Clock input) Data/Command, Low for command and High for data IM is connected to 1 to VCC (3.3V); This OLED integrates the SH1107

₹934.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Working Voltage:3.3V

Communication Interface:/IIC

Controller:SH1107

Resolution:64 × 128

Display Area:14.7 × 29.42 (mm)

Pixel size:0.15 × 0.15 (mm)

Dimension: 30 × 39.5 (mm)

Color: Black/White

Overview

1.3inch LCD HAT, SPI/I2C interfaces

Specification

Working Voltage:3.3V

Communication Interface:/IIC

Controller:SH1107

Resolution:64 × 128

Display Area:14.7 × 29.42 (mm)

Pixel size:0.15 × 0.15 (mm)

Dimension: 30 × 39.5 (mm)

Color: Black/White

Pins

PIN Description

VCC Power input(3.3V)

GND Ground

DIN MOSI pin of SPI (Data input)

CLK SCLK pin of SPI (Clock input)

CS Chip selection, low active

DC Data/Command, Low for command and High for data

RST Reset, Low active

Hardware Configuration

The OLED module provides two drive interfaces: 4-wire SPI and I2C. There is a resistor that can be soldered on the back of the module, and the corresponding communication mode can be selected through the selection of the resistor, as shown in the figure: The module uses 4-wire SPI communication mode by default, that is, IM is connected to 0 by default (1 and 0 do not represent the level, just the welding method of connecting or connecting the resistance, the specific hardware link is shown in the following table): Note: The above picture is the welding on the hardware, the following table is the actual hardware connection

Communication Method IM

4-wire SPI 0

I2C 1

The specific hardware configuration is as follows:

Using 4-wire SPI:

That is, the factory program setting: IM is connected to 0 and connected to the ground;

Using I2C:

IM is connected to 1 to VCC (3.3V); When using I2C: The high and low state of DC can control the address of the slave device. If it receives a low level, then the 7-bit address of I2C is: 0x3C; PS: The program defaults to SPI mode. If you need to switch the mode, please modify DEV_Config.h. For details, please refer to the program description - bottom hardware interface - interface selection

OLED and its controller

This OLED integrates the SH1107 controller which has 128x128 bits SRAM, supports 128x128 resolution. The controller features SPI/IIC/ 6800/8080 interface and 256 brightness levels. The resolution of this 1.3inch OLED is only 64x128, only half of the SRAM is used. This OLED use four-line SPI and I2C interface for communicating, which supports higher compatibility and speed.

Package Included :

1 X 1.3inch OLED Display Module

Specifications

Working Voltage:3.3V
Communication Interface/IIC
Controller:SH1107
Resolution:64 × 128
Display Area:14.7 × 29.42 (mm)
Pixel size:0.15 × 0.15 (mm)
Dimension30 × 39.5 (mm)
ColorBlack/White

More in Arduino Boards

You might also need