About this product
KIT INCLUDED:
Arduino Nano with USB Cable - 1
TTP224B 4-channel capacitive module - 1
Power bank-1(not included in kit)
Jumper wire male to female – 40 piece
Jumper wire male to male – 40 piece
Breadboard 840 points - 1
16*2 lcd with i2c module - 1
HARDWARE REQUIRED
Arduino Nano with USB Cable - 1
TTP224B 4-channel capacitive module - 1
Power bank-1(not included in kit)
Jumper wire male to female – 40 piece
Jumper wire male to male – 40 piece
Breadboard 840 points - 1
16*2 lcd with i2c module - 1
SOFTWARE REQUIRED
Arduino IDE 1.8.5 (programmable platform for Arduino)
Click To Download :https://www.arduino.cc/en/Main/Software
SPECIFICATIONS
TTP224B 4-CHANNEL CAPACITIVE TOUCH MODULE
On-board TTP224 capacitive touch 4 key induction IC
On-board 4 road level indicator.
Working voltage: 2 V to 5.5 V DC
Adjustable output mode, key output mode, longest time and fast/low power output
PCB board size: 35(mm) x29 (mm).
ARDUINO NANO
Arduino Pro Mini
Microcontroller
ATmega168
Operating Voltage
3.3V or 5V
Input Voltage
3.35 -12 V (3.3V model) or 5 - 12 V (5V model)
Digital I/O Pins
14 (of which 6 provide PWM output)
Analog Input Pins
8
DC Current per I/O Pin
40 mA
Flash Memory
16 KB (of which 2 KB used by bootloader)
SRAM
1 KB
EEPROM
512 bytes
Clock Speed
8 MHz (3.3V model) or 16 MHz (5V model)
PIN DESCRIPTION
TTP224B 4-CHANNEL CAPACITIVE TOUCH MODULE
VCC: 2V to 5.5V DC
GND: ground
OUT4: high/low output
OUT3: high/low output
OUT2: high/low output
OUT1: high/low output
ARDUINO NANO
RAW
For supplying a raw (regulated) voltage to the board
VCC
The regulated 3.3 or 5 volt supply
GND
Ground pins
RX
Used to receive TTL serial data
TX
Used to transmit TTL serial data
2 and 3
Digital I/O pins. These pins can also be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value
3, 5, 6, 9, 10, and 11
Digital I/O pins. They can also be configured to provide 8-bit PWM output
10, 11, 12 and 13
Digital I/O pins. They can also be configured as SPI pins;
10 - (SS), 11 - (MOSI), 12 - (MISO) and 13 - (SCK)
A0 to A3
Analog input pins
A4 and A5.
Analog input pins. They can also be used as IIC pins;
A4 - (SDA) and A5 – (SCL).
A6 and A7
Analog input pins
Reset
The microcontroller can be reset by bringing this pin low
CIRCUIT CONNECTION
Out1 of TTP224 to the Nano D11
Out2 of TTP224 to the Nano D10
Out3 of TTP224 to the Nano D9
Out4 of TTP224 to the Nano D8
Ground to the negative rail and Vcc to the positive rail
I2C module Vcc to positive rail and ground to negative rail
I2C module sda pin to Nano A4 and scl to A5
CODE
Click to see the code or copy the link:
https://docs.google.com/document/d/e/2PACX-1vT7XfN3XPQkFHLgTqkjECB62lWK4TsB1RyxRtlPCCGaFYCPsjmTjW7ApuxuG24Tr3kfiMX6wmrd56dE/pub
WORKING
Upload the code and see the output.