Test a GY-9150 MPU-9150 3-Axis Electronic Compass Acceleration Gyroscope Module Interfacing with Arduino Uno - KT701

SKU KT701

Arduino IDE 1.8.5 (programmable platform for Arduino) The MPU-9150 consists of a 9-axis Motion Fusion which combines both acceleration and rotational motion which helps in heading

₹1878.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDED:

Jumper Wires (male to male) – 40 pieces

Breadboard 840 points – 1

9V battery with DC Jack – 1

Arduino Uno with USB cable – 1

GY-9150 MPU-9150 9-Axis Altitude Three-Axis Electronic Compass Acceleration Gyroscope Module - 1

HARDWARE REQUIRED

Jumper Wires (male to male) – 40 pieces

Breadboard 840 points – 1

9V battery with DC Jack – 1

Arduino Uno with USB cable – 1

GY-9150 MPU-9150 9-Axis Altitude Three-Axis Electronic Compass Acceleration Gyroscope Module - 1

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download :https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

GY-9150 MPU-9150 Three-Axis Acceleration Gyroscope Module The MPU-9150 consists of a 9-axis Motion Fusion which combines both acceleration and rotational motion which helps in heading information into a single data stream for the application. Such technology integration provides a smaller footprint and has better cost advantages compared to discrete gyroscope, accelerometer, plus magnetometer solutions.

It also inculcates a Digital Motion Processor (DMP) also known as hardware accelerator engine.

The Accelerometer's scale can be set to ±2g, ±4g, ±6g, ±8g, or ±16g.

The Gyroscope also supports ±250, ±500, and ±2000 °/s.

Small in size

MPU-9150 internal integration (three-axis gyroscope + tri-axial accelerometer + Tri-axis compass)

Module Model: GY-9150, chip: MPU-9150

Supply voltage: 3.3v-5v

Communication: standard IIC communication protocol

It also consists of in-built16 bit AD converter, 16-bit data output

Tri-axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g

Tri-axis compass with a full scale range of ±1200µT

PIN DESCRIPTION

GY-9150 MPU-9150 Three-Axis Acceleration Gyroscope Module

S.NO

NAME (Adruino)

DESCRIPTION

1

GND

GND (It grounds the Input and completes the circuit)

2

VCC

3.3V (Recommended Voltage)

3

SDA

SDA (Serial Data Pin is used for I2C communication)

4

SCL

SCL (Serial Clock Pin is used for I2C serial clock)

5

EDA

Auxiliary I2C master serial data (It allows an external system processor to act as master and directly communicate to the external sensors connected to the auxiliary I2C bus pins)

6

ECL

Auxiliary I2C Master serial clock (It allows an external system processor to act as master and directly communicate to the external sensors connected to the auxiliary I2C bus pins)

7

ADO

I2C Slave Address LSB (The LSB of the of the I2C slave address is set by pin 9)

8

INT

Interrupt digital output

CIRCUIT CONNECTION

The GND of Arduino is being connected to the GND pin of the MPU9150.

The SDA (Serial Data) pin of Arduino is being connected with the SDA pin used inMPU9150 for I2C bidirectional communication.

The Arduino UNO can be powered by the 9V battery which helps in executing the entire further process.

The SCL (Serial Clock) pin of Arduino is being connected with the SCL pin used inMPU9150 for I2C Serial Clock.

The VCC of the MPU9150 is being connected to the 3.3V as per recommended as higher voltage can damage it.

The EDA is the Auxiliary I2C master serial data which allows an external system processor to act as master and directly communicate to the external sensors connected to the auxiliary I2C bus pins. But it is not used in this particular circuit.

The ECL is the Auxiliary I2C Master serial clock which allows an external system processor to act as master and directly communicate to the external sensors connected to the auxiliary I2C bus pins. But it is not used in this particular circuit.

The AD0 Pin is the I2C Slave Address LSB. The LSB (Least Significant Byte) of the of the I2C slave address is set by Arduino Pin (Mostly Pin 9). But it is not used in this particular circuit.

The INT Pin is the Interrupt Pin. It is for the Digital Output. But it is not used in this particular circuit.

CODE Click to see code here: https://docs.google.com/document/d/e/2PACX-1vTzGZQNgKtezfRIQyzaVrBBhjvooeOF2cX3ay_qb4rjkMZHA4787biYqskH2uBeaFt3O_gWwmFiJLcY/pub?embedded=true

LIBRARIES REQUIRED Install the Libraries: I2C.h

MPU6050.h

WORKING

This particular Arduino based project consists of a 3-axis accelerometer, 3-Axis gyroscope, 3-Axis magnetometer and a Digital Motion Processor which helps in enabling Motion Interfacing. The MPU-9150 is also designed to interface with multiple non-inertial digital sensors, such as pressure sensors, on its auxiliary I2C port to produce a 10-Axis sensor fusion output. The MPU-9150 is a System in Package (SiP) which combines two chips: The MPU-6050, which contains a 3-axis gyroscope, 3-axis accelerometer, and an onboard Digital Motion Processor (DMP) capable of processing complex MotionFusion algorithms; and the AK8975, a 3-axis digital compass. The device has integrated 6-axis MotionFusion algorithms which accesses all internal sensors to gather a full set of sensor data. It also supports a variety of advanced motion-based applications entirely on-chip. The MPU-9150 enables low-power Motion Processing in portable applications with reduced processing requirements for the system processor. Output:

Block Diagram:

More in Arduino Boards

You might also need