SpeedyBee

SpeedyBee F405 Mini Flight Controller BLS 35A 20×20 Stack F405 Flight Controller With BLHeli_S ESC Compact Flight Controller For Drones Lightweight Flight Controller For FPV Racing Easy-to-install and

SKU RS7363

The SpeedyBee F405 Mini Flight Controller BLS 35A 20×20 Stack is a powerful and versatile flight controller for drones and an ESC stack that is perfect for drones ranging from 2 to

₹11048.70

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Description:

The SpeedyBee F405 Mini Flight Controller BLS 35A 20×20 Stack is a powerful and versatile flight controller for drones and an ESC stack that is perfect for drones ranging from 2 to 5 inches. It features an upgraded F405 flight controller chip, built-in Bluetooth for wireless Betaflight tuning, and a 35A 4-in-1 ESC that can handle even the most demanding flight maneuvers.

Specifications:

Product Name SpeedyBee F405 Mini Flight Controller

MCU STM32F405

IMU(Gyro) ICM42688P

USB Port Type Type-C

Barometer Built-in

OSD Chip AT7456E chip

BLE Bluetooth

Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise, Bluetooth functionality will not be available.

Wireless FC Firmware Flashing NOT Supported. Please connect to the Betaflight configurator on the PC to do an FC firmware update

Wireless Blackbox Download & Analysis NOT Supported. Please connect to the Betaflight configurator on the PC to do a black box analysis.

WIFI Not supported

DJI Air Unit Connection Way Direct soldering

DJI Air Unit Compatibility Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD, and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.

black box 8MB Onboard Flash

BetaFlight Camera Control Pad Yes(CC pad on the front side)

Current Sensor Input Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.

Power Input 3-6S LiPo. The flight controller is powered through the G, V wires of the 8-pin harness or G, V pads from the bottom side of the flight controller.

5V Output 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.

9V Output 1 group of 9V output, one +9V pad on front side. The total current load is 3A.

3.3V Output Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.

4.5V Output Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal M1 - M4 wires or soldering pads on the bottom side.

CART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry UART R5(UART5)

I2C Supported. DA & CL pads on the front side. Used for magnetometer, sonar, etc

Traditional Betaflight LED Pad Supported. 5V, G, and LED pads on the bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.

Buzzer BZ+ and BZ- pad used for 5V Buzzer

BOOT Button Supported. Press and hold the BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.

RSSI Input Not Supported

Smart Port / F.Port Not Supported

Supported Flight Controller Firmware BetaFlight(Default), INAV

Firmware Target Name SPEEDYBEEF405MINI

Mounting

20 x 20mm 3.5mm hole diameter ,Compatible with M2 and M3 screws/Silicone grommets.

Product Name SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC

Firmware BLHeli_S J-H-40

Continuous Current 35A*4

Burst Current 45A(5seconds)

ESC Protocol DSHOT300/600

Power Input 3-6S LiPo

Power Output VBAT(Battery voltage, used to power the flight controller)

Current Sensor Support (Scale=250 Offset=-500)

ESC Telemetry Not supported

Mounting

20 x 20mm ∅3.5mm hole size,compatible with M2 and M3 screws/Silicone grommets.

Features:

Sufficient 4x UARTs for your receiver, VTX, camera, and GPS

Two independent 5V 2A BEC and 9V 3A BEC outputs

USB power for GPS – no battery needed

17mm cutouts for FPV camera in tight builds

Onboard 8MB Blackbox storage

Package Included:

Sufficient 4x UARTs for your receiver, VTX, camera, and GPS

Two independent 5V 2A BEC and 9V 3A BEC outputs

USB power for GPS – no battery needed

17mm cutouts for FPV camera in tight builds

Onboard 8MB Blackbox storage

Specifications

Product Name
SpeedyBee F405 Mini Flight Controller
MCU
STM32F405
IMU(Gyro)
ICM42688P
USB Port Type
Type-C
Barometer
Built-in
OSD Chip
AT7456E chip
BLE Bluetooth
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise, Bluetooth functionality will not be available.
Wireless FC Firmware Flashing
NOT Supported. Please connect to the Betaflight configurator on the PC to do an FC firmware update
Wireless Blackbox Download & Analysis
NOT Supported. Please connect to the Betaflight configurator on the PC to do a black box analysis.
WIFI
Not supported
DJI Air Unit Connection Way
Direct soldering
DJI Air Unit Compatibility
Compatible with all DJI Air UnitsDJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD, and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.
black box
8MB Onboard Flash
BetaFlight Camera Control Pad
Yes(CC pad on the front side)
Current Sensor Input
Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input
3-6S LiPo. The flight controller is powered through the G, V wires of the 8-pin harness or G, V pads from the bottom side of the flight controller.
5V Output
4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output
1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output
Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output
Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal
M1 - M4 wires or soldering pads on the bottom side.
CART
6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry
UART R5(UART5)
I2C
Supported. DA & CL pads on the front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad
Supported. 5V, G, and LED pads on the bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.
Buzzer
BZ+ and BZ- pad used for 5V Buzzer
BOOT Button
Supported. Press and hold the BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
RSSI Input
Not Supported
Smart Port / F.Port
Not Supported
Supported Flight Controller Firmware
BetaFlight(Default), INAV
Firmware Target Name
SPEEDYBEEF405MINI
Mounting
20 x 20mm 3.5mm hole diameter ,Compatible with M2 and M3 screws/Silicone grommets.
Product Name
SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
Firmware
BLHeli_S J-H-40
Continuous Current
35A*4
Burst Current
45A(5seconds)
ESC Protocol
DSHOT300/600
Power Input
3-6S LiPo
Power Output
VBAT(Battery voltage, used to power the flight controller)
Current Sensor
Support (Scale=250 Offset=-500)
ESC Telemetry
Not supported
Mounting
20 x 20mm ∅3.5mm hole size,compatible with M2 and M3 screws/Silicone grommets.

More in Flight Controllers

You might also need