About this product
KIT INCLUDES
Arduino Uno with USB cable - 1
Breadboard 400 points - 2
Servo motor sg90 - 1
Capacitor(100uf) - 1
Fingerprint sensor (gt511c) - 1
16*2 LCD display - 1
Jumper wires male to male - 40 pieces
Jumper Wire (male to female ) – 40 pieces
9Vbattery snapper - 1
dc jack snapper – 1
9v Battery - 1
HARDWARE REQUIRED
Arduino Uno with USB cable - 1
Breadboard 400 points - 2
Servo motor sg90 - 1
Capacitor(100uf) - 1
Fingerprint sensor (gt511c) - 1
16*2 LCD display - 1
Jumper wires male to male - 40 pieces
Jumper Wire (male to female ) – 40 pieces
9Vbattery snapper - 1
dc jack snapper – 1
9v Battery - 1
SOFTWARE REQUIRED
Arduino IDE 1.8.5 (programmable platform for Arduino)
Click To Download :https://www.arduino.cc/en/Main/Software
INSTALL LIBRARY
For servo Motor: inbuilt library of Arduino or Download from https://drive.google.com/drive/folders/1XEyFZik_ENYtE4LOf3mOP3kqfqH3FNh2
16*2 LCD Display (Liquid Display): inbuilt library of Arduino
GT511C fingerprint Scanner: Click on this link to download this library: https://drive.google.com/open?id=1g3E45sI85X5k6p8wPOYKOTOs_ST3xxJg
CIRCUIT CONNECTION
Connect the GT511 Fingerprint scanner to arduino with fingerprint scanner’s red wire to 3.3v of Arduino uno
Black wire of fingerprint scanner to arduino uno’s ground pin
Green wire of fingerprint scanner toarduino uno’s digital pin D7
White wire of Fingerprint scanner to Arduino’s digital pin D8
Download the code given in the link below:
CODE-1
Click to see the code or copy the link
https://goo.gl/Bqbh5C
Now upload code 1
set the fingerprints using sdk software
Download the SDK Software:
https://learn.sparkfun.com/tutorials/fingerprint-scanner-hookup-guide?_ga=2.83121109.213978244.1515759134-440643312.1494316028
The image will be shown as given below:
when open as administrator then set com port and baud rate then enroll fingerprint upto 200 fingerprints as required.
Now connect the lcd to the breadboard
Connect pin 1 of LCD to ground
Connect pin 2 of LCD to positive rail on breadboard
Connect pin 3 of LCD to negative rail on breadboard
Connect pin 4 of LCD to digital pin 12 of arduino uno
Connect pin 5 of LCD to negative rail on breadboard
Connect pin 6 of LCD to pin 11 of arduino uno
Connect pin 11 of LCD to pin 5 of arduino uno
Connect pin 12 of LCD to pin 4 of arduino uno
Connect pin 13 of LCD to pin 3 of arduino uno
Connect pin 14 of LCD to pin 2 of arduino uno
Connect pin 15 of LCD to positive rail on breadboard
Connect pin 16 of LCD to negative rail on breadboard
Connect to breadboard with positive and negative rail
Connect a 100uf capacitor to the breadboard between Positive and negative rail
Now connect a servo motor
Connect orange wire of fingerprint scanner goes to pin 10 of arduino uno
Connect red wire to positive rail on breadboard and brown wire to negative rail on breadboard.
Now upload code 2
Click to download the code
CODE-2
Click to download the code or copy the link
https://goo.gl/5HWu9B
WORKING
In this security system using fingerprint sensor we used GT511C finger print sensor , in this we have to enroll the fingerprint using SDK software in this we can enroll up to 200 fingerprints. When we apply fingerprint
The gate will for the delay we provided and then it will close. The capacitor is used to reduce the spike voltage.