Measure the value of water flow using water flow sensor and DC water pump 12 V interfacing with Arduino uno - KT860

SKU KT860

Pipe – 1(not included in kit) Arduino IDE ( programmable software for Arduino boards ) Flow sensor Yellow Wire is output and it gives pulses in proportion with flow.

₹2398.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

HARDWARE REQUIRED

Arduino Uno with USB cable - 1

Water Flow Sensor - 1

Single stand wire 2m -1

LCD 16*2 Display - 1

Breadboard 400 point – 1

Pipe – 1(not included in kit)

12v DC water pump – 1

12V amp adapter – 1

Potentiometer 10 k – 1

9v battery-1

snapper – 1

Jumper wire male to male -40 piece

jumper wire male to female – 40 piece

SPECIFICATIONS

16*2 LCD DISPLAY

LCD Display Mode: STN, Positive, Transflective

Display Color: Deep Blue/ Yellow Green

Viewing Angle: 6H

Driving Method : 1/16 duty, 1/5 bias

Back Light : Yellow-Green LED backlight

Outline Dimension: 803615.8 MAX

CAUTIONS

• The LCD panel is made by glass. Any mechanical shock (eg. dropping from high place) will damage the LCD module. • Do not add excessive force on the surface of the display, which may cause the Display color change abnormally. • The polariser on the LCD is easily get scratched. If possible, do not remove the LCD protective film until the last step of installation. • Never attempt to disassemble or rework the LCD module. • Only Clean the LCD with Isopropyl Alcohol or Ethyl Alcohol. Other solvents (eg.water) may damage the LCD. • When mounting the LCD module, make sure that it is free form twisting, warping and distortion. • Ensure to provide enough space(with cushion) between case and LCD panel to prevent external force adding on it, or it may cause damage to the LCD or degrade the display result. • Only hold the lCD module by its side. Never hold LCD module by add force on the heat seal ot TAB. • Never add force to component of the LCD module. It may cause invisible damage or degrade of the reliability. • LCD module could be easily damaged by static electricity. Be careful to maintain an optimum anti-static work environment to protect the LCD module. • When peeling off the protective film from LCD, static charge may cause abnormal display pattern. It is normal and will resume to nomal in a short while. • Take care and prevent get hurt by the LCD panel sharp edge. • Never operate the LCD module exceed the absolute maximum ratings. • Keep the signal line as short as possible to prevent noisy signal applying to LCD module. • Never apply signal to the LCD module without power supply. • IC chip(eg. TAB or COG) is sensitive to the light. Strong lighting environment could possibly cause malfunction. Light sealing structure casing is recommend. • LCD module reliability may be reduced by temperature shock.

WATER FLOW SENSOR

Sensor Type: Hall effect

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)

Max current draw: 15mA @ 5V

Output Type: 5V TTL

Working Flow Rate: 1 to 30 Liters/Minute

Working Temperature range: -25 to +80℃

Working Humidity Range: 35%-80% RH

Accuracy: ±10%

Maximum water pressure: 2.0 MPa

Output duty cycle: 50% +-10%

Output rise time: 0.04us

Output fall time: 0.18us

Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)

Pulses per Liter: 450

Durability: minimum 300,000 cycle

SOFTWARE REQUIRED

Arduino IDE ( programmable software for Arduino boards )

You can download the software from this link : https://www.arduino.cc/en/Main/Software

PIN DESCRIPTION

10K POTENTIOMETER

16*2 LCD DISPLAY

WATER FLOW SENSOR

CIRCUIT DESCRIPTION

Flow sensor Yellow Wire is output and it gives pulses in proportion with flow. Flow Sensor Connections Yellow --- Pin 2 Red --- +5V Black --- GND

LCD Connections LCD RS pin to digital pin 12 LCD Enable pin to digital pin 11 LCD D4 pin to digital pin 6 LCD D5 pin to digital pin 5 LCD D6 pin to digital pin 4 LCD D7 pin to digital pin 3 LCD R/W pin to ground 1K resistor: One end to ground Another end to LCD VO pin (pin 3)

CODE click to see the code https://docs.google.com/document/d/e/2PACX-1vQp-DYSluOk_Q_PVx5ZkdDL9RjJiDOpfbo7XQfNN5CS-92FbX_3lrSKXbf6x1Opb_DuVEgHM5OqT4Of/pub

WORKING 1. Blow air or allow water flow through the sensor 2. Observe the reading on LCD or Serial Monitor 3. Readings get updated at every 1 Sec HERE we connect the water flow pump 12 dc motor use for flow the water between the water flow sensor you see the result on lcd 16*2

More in Arduino Boards

You might also need