Measure the Value of Moisture in soil and show the output using 5 Led interfacing with Arduino uno - KT878

SKU KT878

Arduino IDE 1.8.5 (programmable platform for Arduino) The two probes are acting as a variable resistor – more water in the soil means better conductivity and results in a lower

₹1348.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

Arduino uno with Usb cable – 1

Breadboard (400 point) - 1

Jumper wire male to female– 40 pieces

Jumper wire male to male – 40 pieces

LED – 7

Soil (not included in kit)

Soil moisture sensor – 1

HARDWARE REQUIRED

Arduino uno with Usb cable – 1

Breadboard (400 point) - 1

Jumper wire male to female– 40 pieces

Jumper wire male to male – 40 pieces

LED – 7

Soil (not included in kit)

Soil moisture sensor – 1

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download :https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

SOIL MOISTURE SENSOR KIT The two probes are acting as a variable resistor – more water in the soil means better conductivity and results in a lower resistance and a higher SIG out. Your analog readings will vary depending on what voltage you use for Vcc as well as the resolution of your ADC pins.

PIN DESCRIPTION

SOIL MOISTURE SENSOR KIT

The two probes are acting as a variable resistor – more water in the soil means better conductivity and results in a lower resistance and a higher SIG out. Your analog readings will vary depending on what voltage you use for Vcc as well as the resolution of your ADC pins.

LED

CIRCUIT CONNECTION

Digital Pin 2 Green wire led Digital Pin 3 Green wire led Digital Pin 4 Green wire led Digital Pin 5 Yellow wire led Digital Pin 6 Red wire led Connect the cathode or (-) lead from the LED to the Arduino. **Here you can put a 1k resistor between anode (+) and the positive rail. Connect the anode or (+) lead from the LED to the + positive rail of the breadboard. The moisture has very well defined pin out. Connect the ground to the ground rail, power to the power rail. Connect the "AC" Labeled pin on the moisture sensor to analog input 0 pin on the Arduino. *note, the moisture sensor It has two outs one labeled "AC" and one labeled "DC". The "AC", is a serial signal 0-5 volts that when fully dry it outputs 5 volts, when fully wet, 0 volts. The "DC", is configured with the trim pot and is brought high when the moisture level reaches a desired point.

Connect the two pins from the Sensor to the two pins on the Amplifier circuit via hook up wires.

Connect the Vcc from the Amplifier to the 3.3V pin on the Arduino and the Gnd pin to the Gnd pin on the Arduino.

Now connect the Analog Data Pin to the A0 pin on the Arduino (Since I'm interested in Analog Data).

CODE

CLICK TO SEE THE CODE https://docs.google.com/document/d/e/2PACX-1vQAhz74-yeWaL7QX7QbSV7Q3Xv2ceHeFVI_-unMNKhALenKacbOX3wwZzXCIfnnmHJq0LInZGZSy5Bs/pub

WORKING Connect the Arduino board and put the sensor kit into the sand glass you will see the output as the intensity of glowing of led.

More in Arduino Boards

You might also need