REES52

Make an IOT Weather Station Kit using DHT22 Module and OLED interfacing with ESP8266-12E compatible Arduino Uno - KT861

SKU KT861

In this project, we designed an IOT based temperature and Humidity sensor using Node MCU and DHT11 by interfacing with the BLYNK application.

₹1873.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

INTROCUCTION

In this project, we designed an IOT based temperature and Humidity sensor using Node MCU and DHT11 by interfacing with the BLYNK application.

HARDWARE REQUIRED

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1pc

NodeMcu USB Cable - 1pc

DHT22 Sensor - 1pc

Jumper Wires (male to male) – 20 pcs each

830 pt. Breadboard - 1pc

0.96 inch OLED Display -1pc

10K Ohm resistor - 2pcs

SOFTWARE REQUIRED

Arduino IDE 1.8.10 (programmable platform for Arduino)

Click here to download the software

SPECIFICATIONS

NodeMCU ESP8266 CP2102 Module:

ESP8266 CP2102 NodeMCU LUA ESP-12E WIFI Serial Wireless Module

Built-in Micro-USB, with flash and reset switches, easy to program

Full I/O port and Wireless 802.11 supported, direct download, no need to reset

Arduino compatible works great with the latest Arduino IDE/Mongoose IoT/Micro Python

DHT22 Sensor:

Voltage: 3 to 5V power and I/O

Current: 2.5mA max current use during conversion (while requesting data)

Humidity Range: Good for 0-100% humidity readings with 2-5% accuracy

Temperature Range: -40 to 80°C temperature readings ±0.5°C accuracy

Sampling rate: No more than 0.5 Hz (once every 2 seconds)

4 pins, 0.1' spacing.

OLED Display:

Display: 0.96" OLED Display

Dot matrix size: 128x64

Controller IC: SSD1306

Working Voltage: DC 3.3v - 5v

Colour: Blue

INSTALL LIBRARY

Weather Station by Daniel Eichhorn

APPLICATION REQUIRED

BLYNK:

Download from the Google Play Store and the Apple Store

CIRCUIT CONNECTION

Connect the OLED pins to the NodeMCU, as described below and shown in the below electrical diagram:

SDA ==> D1 (5)

SCL* ==> D2 (4) * Also, you can find "SDC" in the text

VCC ==> The SSD1306 can be powered directly by 5v (external) or 3.3v from the NodeMCU module.

GND ==> GND

Once we have connected the display, let's download and install its library on our Arduino IDE.

Below the library that must be downloaded and installed on your Arduino IDE: Click to open drive

Once you restart the IDE, the library should be already installed.

The library supports I2C protocol to access the OLED display using the built in Wire.h library:

CODE

Click to open in Drive

Must mention your correct Wi-Fi ID and Password in the code

GETTING INDOOR DATA

Usually, you will use the sensor on distances less than 20m a 10K ohm resistor should be connected between the Data and VCC pins. The Output pin will be connected to NodeMCU pin D3 (Given in the Diagram below)

Once the sensor is installed on our module, download the DHT library from the Adafruit GitHub repository and install it in your Arduino's Library file. Once you reload your Arduino IDE, the "DHT sensor library" should be installed.

Click to download the Outdoor weather data by clicking on this Weather Underground. ( https://www.wunderground.com/ )

You will need to create an account on their website and get a Weather API key. Do it following the instructions at below link: https://www.wunderground.com/weather/api

More in WiFi & IoT Modules

You might also need