REES52

Make an IOT LDR Alarm Circuit Using LDR Module and NodeMCU ESP8266-12E Wi-Fi Module compatible with Arduino Uno - KT571

SKU KT571

In this project, we will design an IOT-based LDR alarm circuit using Node MCU ESP8266-12E Wi-Fi Board and LDR module.

₹1123.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

INTRODUCTION

In this project, we will design an IOT-based LDR alarm circuit using Node MCU ESP8266-12E Wi-Fi Board and LDR module. When the value exceeds the set value, the alarm will start ringing.

HARDWARE REQUIRED

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1pc

NodeMcu USB Cable - 1pc

LDR Module -1pc

Jumper Wires (male to male) – 20 pcs

830 pt. Breadboard - 1pc

B-10 Buzzer - 1pc

Led 5mm-1pc

SOFTWARE REQUIRED

Arduino IDE 1.8.10 (programmable platform for Arduino)

Click here to download the software

SPECIFICATIONS

NodeMCU ESP8266 CP2102 Wireless Module:

The development board equips the ESP-12E module containing the ESP8266 chip, having a Tensilica Xtensa® 32-bit LX106 RISC microprocessor which operates at 80 to 160 MHz adjustable clock frequency and supports RTOS.

Operating Voltage: 2.5v to 3.6v

On-board 3.3V 600mA regulator

80mA Operating Current

20 µA during Sleep Mode

ESP8266 CP2102 NodeMCU LUA ESP-12E WIFI Serial Wireless Module

Built-in Micro-USB, with flash and reset switches, easy to program

Full I/O port and Wireless 802.11 supported, direct download, no need to reset

Arduino compatible works great with the latest Arduino IDE/Mongoose IoT/Micro Python

WARNING:

The ESP8266 requires a 3.3v power supply and 3.3v logic levels for communication. The GPIO pins are not 5v-tolerant! You must do some level shifting if you want to interface the board with 5v (or higher) components.

LDR Module:

The Light Dependent Resistor (LDR) is just another special type of Resistor and hence has no polarity

Operating Voltage: 3.3V to 5V DC

Operating Current: 15ma

Output Digital - 0v to 5v, Adjustable trigger level from preset

Output Analogue - 0v to 5v based on light falling on the LDR

Pin Description:

VCC = 3.3V to 5V DC

GND = Ground

S = Output

CIRCUIT CONNECTION

Connect the “A0 (Signal)” pin of the LDR module to the “A0” pin of NodeMCU ESP8266-12e Wi-Fi Module.

Connect the “GND” pin of the LDR module to GND pin of NodeMCU ESP8266-12e Wi-Fi Module.

Connect the +5v pin of the LDR module to the 3.3v pin of NodeMCU ESP8266-12e Wi-Fi Module.

Connect the LED ground pin to the GND pin of the NodeMCU ESP8266-12e Wi-Fi Module.

Connect LED VCC to D2(GPIO4) pin of NodeMCU ESP8266-12e Wi-Fi Module.

Connect Buzzer Gnd to Gnd pin of NodeMCU ESP8266-12e Wi-Fi Module.

Connect Buzzer Positive to D1 (GPIO5) pin of NodeMCU ESP8266-12e Wi-Fi Module.

CODE

Click to open in Drive

WORKING AND OUTPUT

Welcome to the IoT-based project in which we are using an LDR Module using the ESP8266-12E wifi module. When Light falls upon an LDR Module and exceeds the set value in the code, then the buzzer will start beeping.

DOCUMENT

KT571 - Click to open👈

More in WiFi & IoT Modules

You might also need