REES52

Make an IoT based Temperature Level Indicator using LEDs and DHT11 Module with ESP8266-12e Wi-Fi Board compatible with Arduino Uno - KT569

SKU KT569

In this project, we will design an IOT-based temperature level indicator using a DHT11 Temperature and humidity sensor module and an LED in which the Temperature level will be

₹1198.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

INTRODUCTION

In this project, we will design an IOT-based temperature level indicator using a DHT11 Temperature and humidity sensor module and an LED in which the Temperature level will be shown on the LED according to the Temperature value.

HARDWARE REQUIRED

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1pc

NodeMcu USB Cable - 1pc

DHT11 Module -1pc

Jumper Wires (male to male) – 20 pcs

830 pt. Breadboard - 1pc

Led 5mm-3pcs

SOFTWARE REQUIRED

Arduino IDE 1.8.10 (programmable platform for Arduino)

Click here to download the software

SPECIFICATIONS

NodeMCU ESP8266 CP2102 Module:

ESP8266 CP2102 NodeMCU LUA ESP-12E WIFI Serial Wireless Module

Built-in Micro-USB, with flash and reset switches, easy to program

Full I/O port and Wireless 802.11 supported, direct download, no need to reset

Arduino compatible works great with the latest Arduino IDE/Mongoose IoT/Micro Python

DHT11 Module:

Operating Voltage: 3.5v to 5.5v

Operating current: 0.3mA (measuring) 60uA (standby)

Output: Serial data

Temperature Range: 0°C to 50°C

Humidity Range: 20% to 90%

Resolution: Temperature and Humidity both are 16-bit

Accuracy: ±1°C and ±1%

1

Vcc

Power supply 3.5V to 5.5V

2

Data

Outputs both Temperature and Humidity through serial Data

3

Ground

Connected to the ground of the circuit

LIBRARY REQUIRED

DHT11 - Click to open 👈

Adafruit Sensor Library - Click to open 👈

CIRCUIT CONNECTION

Connect the “S” pin of the DHT11 module to pin D5 of the NodeMCU ESP8266-12e board.

Connect the “V” pin of the DHT11 module to the pin 3v3 NodeMCU ESP8266-12e board.

Connect the ground pin of the DHT11 module to the ground pin of the NodeMCU ESP8266-12e board.

Connect the positive leg of LED1 to the D8 pin of NodeMCU ESP8266-12e board.

Connect the positive leg of LED2 to the D7 pin of NodeMCU ESP8266-12e board.

Connect the positive leg of LED3 to the D6 pin of NodeMCU ESP8266-12e board.

Connect the GND leg of all LEDs to the GND rail on the breadboard.

CODE

Click to open in Drive

WORKING AND OUTPUT

Welcome to the Node MCU-based project.

As the 3 LED are connected, the first LED will get ON when the temperature rises greater than 20.

The 2nd LED will get ON when the temperature is between 20 to 27.

The 3rd LED will get ON when the temperature rises more than 29. And the Buzzer get ON indicates “TOO HOT”.

DOCUMENT

KT569 - Click to open👈

More in WiFi & IoT Modules

You might also need