Make an IoT based Gas level controlling system using MQ-2 Gas Sensor module and led with NodeMCU ESP8266-12e Board - KT566

SKU KT566

Jumper Wires (male to male) – 20 pcs each In this project, we have used to design an IOT based Gas level sensor using Node MCU by interfacing with Blynk application and level for

₹1798.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Kit Includes

MQ2 Gas Module - 1

LEDs 5mm (Red & Green) - 2

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1

NodeMcu USB cable - 1

Jumper Wires (male to male) – 20 pcs each

830 pt. breadboard - 1

Introduction In this project, we have used to design an IOT based Gas level sensor using Node MCU by interfacing with Blynk application and level for gas will be shown on Leds. If level increases to high level then red led will glow and if decreases to low level then the green led will glow. HARDWARE REQUIRED

MQ2 Gas Module - 1

LEDs 5mm (Red & Green) - 2

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1

NodeMcu USB cable - 1

Jumper Wires (male to male) – 20 pcs each

830 pt. breadboard - 1

SOFTWARE REQUIRED Arduino IDE 1.8.10 (programmable platform for Arduino) Click To Download: https://www.arduino.cc/en/Main/Software

SPECIFICATIONS NodeMCU ESP8266 CP2102 NodeMCU WIFI Serial Wireless Module The development board equips the ESP-12E module containing ESP8266 chip having Tensilica Xtensa® 32-bit LX106 RISC microprocessor which operates at 80 to 160 MHz adjustable clock frequency and supports RTOS.

Operating Voltage: 2.5V to 3.6V

On-board 3.3V 600mA regulator

80mA Operating Current

20 µA during Sleep Mode

ESP8266 CP2102 NodeMCU LUA ESP-12E WIFI Serial Wireless Module

Built-in Micro-USB, with flash and reset switches, easy to program

Full I/O port and Wireless 802.11 supported, direct download no need to reset

Arduino compatible works great with the latest Arduino IDE/Mongoose IoT/Micro python

WARNING The ESP8266 requires a 3.3V power supply and 3.3V logic levels for communication. The GPIO pins are not 5V-tolerant! If you want to interface the board with 5V (or higher) components, you’ll need to do some level shifting.

MQ-2 Gas Sensor Module

Operating Voltage is +5V

Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO and even methane

Analog output voltage: 0V to 5V

Digital Output Voltage: 0V or 5V (TTL Logic)

Preheat duration 20 seconds

Can be used as a digital or analog sensor

The Sensitivity of Digital pin can be varied using the potentiometer

Pin No:

Pin Name:

Description

1

Vcc

This pin powers the module, typically the operating voltage is +5V

2

Ground

Used to connect the module to system ground

3

Digital Out

You can also use this sensor to get digital output from this pin, by setting a threshold value using the potentiometer

4

Analog Out

This pin outputs 0-5V analog voltage based on the intensity of the gas

LIBRARY REQUIRED

Blynk -

CIRCUIT CONNECTION

Connect MQ2 Module “A0” pin to node MCU pin A0.

Connect MQ2 Module “V” pin to node MCU pin 3v3.

Connect MQ2 Module ground to node MCU ground.

Connect the positive terminal of 1st Led to node MCU Pin D0.

Connect the positive terminal of 2nd Led to node MCU Pin D1.

Connect both negative terminals of LEDs to the GND rail on the breadboard which is connected to the GND pin of NodeMCU.

CODE Click to see the code https://drive.google.com/open?id=1C7d47lML6zx8tgg7Fe_QA5zebh3HBVct

WORKING AND OUTPUT Welcome to the IoT based Gas Detector indicator circuit. To connect with Blynk Application. First, you need to create a new project An AUTH token will be sent to your registered Email ID which you need to note down. You need to insert the key in the given code.

Open the Widget Box and select the Labeled value widget option from the Dropdown list

Click on the plus icon and select Labelled value for The gas level.

define the pins in V1.

Change the min to 0 Max to 1000.

Click on the plus icon to add widget and select a super chart to see the graphical measurement for gas value. Now, press the upload button.

After calculating the MQ2 Gas Sensor Module, the values will be shown on the graphical interface.

Click to watch the tutorial For more tutorials subscribe our channel REES52 on YouTube https://www.youtube.com/channel/UCKuJ1KCjJGat7PrdAcWtu5g

More in WiFi & IoT Modules

You might also need