Make a water level & Temperature Measurement tool using Ultrasonic sensor & DS18B20 Sensor Module with Arduino uno - KT776

SKU KT776

Arduino IDE 1.8.5 (programmable platform for Arduino) This is a waterproofed version of the DS18B20 Arduino Temperature sensor.

₹1275.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

Arduino uno with USB cable - 1

HC-SR04 ultrasonic sensor -1

16x2 LCD Display - 1

DS18B20 temperature sensor - 1

10k potentiometer - 1

Push button - 1

Buzzer B10 - 1

3 LEDs ( R,Y,G)- 2 pieces each

Jumper wires male to female – 40 piece

Jumper wires Male to male – 40 piece

Single stand wire 2mt - 1

Resistor (220 ohm-4, 4.7k ohm-2)

HARDWARE REQUIRED

Arduino uno with USB cable - 1

HC-SR04 ultrasonic sensor -1

16x2 LCD Display - 1

DS18B20 temperature sensor - 1

10k potentiometer - 1

Push button - 1

Buzzer B10 - 1

3 LEDs ( R,Y,G)- 2 pieces each

Jumper wires male to female – 40 piece

Jumper wires Male to male – 40 piece

Single stand wire 2mt - 1

Resistor (220 ohm-4, 4.7k ohm-2)

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download: https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

DS18B20 DIGITAL TEMPERATURE SENSOR This is a waterproofed version of the DS18B20 Arduino Temperature sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125℃ the cable is jacketed in PVC so we suggest keeping it under 100℃. Because they are digital, you don't get any signal degradation even over long distances! The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface so that only one wire (and ground) needs to be connected from a central microprocessor. Usable with 3.0-5.5V systems.

Usable with 3.0V to 5.5V power/data

±0.5℃ Accuracy from -10℃ to +85℃

Usable temperature range: -55 to 125℃ (-67℉ to +257℉)

9 to 12-bit selectable resolution

Uses 1-Wire interface- requires only one digital pin for communication

Unique 64 bit ID burned into the chip

Multiple sensors can share one pin

Temperature-limit alarm system

Query time is less than 750ms

3 wires interface:

Red wire - VCC Black wire - GND Yellow wire – DATA

16*2 LCD DISPLAY

LCD Display Mode: STN, Positive, Transflective

Display Color: Deep Blue/ Yellow Green

Viewing Angle: 6H

Driving Method : 1/16 duty, 1/5 bias

Back Light : Yellow-Green LED backlight

Outline Dimension: 803615.8 MAX

PIN DESCRIPTION

.16*2 LCD DISPLAY

Symbol

External Connection

Function

VSS

Power Supply

Signal GROUND for lcm

VDD

POWER SUPPLY for logic lcm

V0

Contrast Adjust

RS

MPU

Register Select Signal

RW

MPU

Read/Write Select Signal

E

MPU

Operation Enable Signal

DB0~DB3

MPU

Four Low order bidirectional three state bus lines. Used for data transfer between the MPU and LCM. These four are not used between 4 Bit operations.

DB4~DB7

MPU

Four high order bidirectional Three state bus lines used for data transfer between the MPU

A

LED BKL power Supply

Power Supply for BKL

K

NOTE

Color tone may slightly change by Temperature and Driving Condition.

The Color is defined as the inactive/background color

.

CIRCUIT CONNECTION

Connect DS18B20 ground to negative rail and positive to the positive rail and out pin to D6 via4.7k resistor through the 5v pin.

Connect ultrasonic sensor’s Vcc to positive rail on the breadboard, ground to the negative rail, echo to D7 and trigger to D9 of Arduino UNO.

All LEDs negative connects to negative rail and green led positive to D13 via 220-ohm resistor, yellow positive to D8 via 220-ohm resistor and red positive to D10 via 220-ohm resistor

Connect Buzzer’s positive to the positive rail and negative to the negative rail

Connect Push button’s one point to the ground and other to pin 16 of LCD.

Connect10k pot-positive to the positive rail, negative to negative rail and signal pin to PIN 3 of LCD.

Pin 1 of LCD to ground, pin 2 to 5v, pin 4 to D12, pin 5 to ground, pin 6 to D11, pin 11 to D5, pin 12 to D4, pin 13 to D3 and pin 14 to D2, pin 15 to 5v rail.

Connect 5v and ground of UNO to breadboard positive and negative rail.

CODE

https://docs.google.com/document/d/e/2PACX-1vTkxWEP8RTl32Pg0SNHAzajRMeCM6xsG7Iv6g6rNefoUkb_uhqs1eyioZINyAZTZ8MYPnG6Y4NdYvU7/pub

WORKING

This project gives me the info I need about the water level in a water tank. When the level is low, the green LED is ON. When the level is medium, the yellow LED is ON. When the level is HIGH the red LED blinks at the same time with the buzzer sound. The distance from the sensor to water level is measured by the ultrasonic sensor and is printed to the LCD together with the temperature in that tank.The temperature is measured by the DS18B20 sensor

More in Arduino Boards

You might also need