Make a Temperature Controlled Fan using DHT22 and 16*2 LCD interfacing with Arduino uno - KT820

SKU KT820

Arduino IDE 1.8.5 (programmable platform for Arduino) 3 to 5V power and I/O Good for 0-100% humidity readings with 2-5% accuracy Good for -40 to 125°C temperature readings ±0.5°C

₹1873.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

Arduino Uno with USB cable -1

L293D Motor Driver IC -1

DHT22 Sensor - 1

16×2 LCD Display - 1

DC Fan/motor with fan blade - 1

9V Battery with snapper - 1

10KΩ Potentiometer - 1

Breadboard 400 points- 1

Jumper Wire(male to male) – 40 pieces

Single stand wire 2m - 1

HARDWARE REQUIRED

Arduino Uno with USB cable -1

L293D Motor Driver IC -1

DHT22 Sensor - 1

16×2 LCD Display - 1

DC Fan/motor with fan blade - 1

9V Battery with snapper - 1

10KΩ Potentiometer - 1

Breadboard 400 points- 1

Jumper Wire(male to male) – 40 pieces

Single stand wire 2m - 1

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download :https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

16*2 LCD Display

LCD Display Mode: STN, Positive, Transflective

Display Color: Deep Blue/ Yellow Green

Viewing Angle: 6H

Driving Method : 1/16 duty, 1/5 bias

Back Light : Yellow-Green LED backlight

Outline Dimension: 803615.8 MAX

PIN DESCRIPTION

10 K Potentiometer

16*2 LCD Display

DHT22 Sensor

3 to 5V power and I/O

2.5mA max current use during conversion (while requesting data)

Good for 0-100% humidity readings with 2-5% accuracy

Good for -40 to 125°C temperature readings ±0.5°C accuracy

No more than 0.5 Hz sampling rate (once every 2 seconds)

Body size 15.1mm x 25mm x 7.7mm

4 pins with 0.1" spacing

CIRCUIT DESCRIPTION

Connect pin 1 (Enable 1) of L293D to pin 5 of Arduino.

Connect pin 2 (Input 1) of L293D to the pin 4 of Arduino.

Connect pin 3 (Output 1) of L293D to one terminal of the DC motor.

Pins 4 and 5 of the L293D are ground pins, connect these to common ground (battery ground + arduino ground).

Connect pin 6 (Output 2) of L293D to the remaining terminal of the DC motor.

Connect pin 7 (Input 2) of L293D to the pin 3 of Arduino.

Pin 8 is Vcc2, which is the driver/motor power input, connect it to positive of the battery.

Pin 16 is Vcc1, which is logic voltage input (voltage level of control signals provided by Arduino). Connect it to 5V output of Arduino.

After that connect DHT22 sensor to the Arduino, it is using a single wire bus for communication.

First pin is VCC power input, connect it to 5V output of Arduino.

Second pin is DATA output, connect it to pin 6 of Arduino.

Third pin is NOT USED.

Fourth pin is Ground, connect it to ground.

Now we can connect 16×2 LCD to the Arduino.

Pin 1 is VSS, connect it to ground.

Pin 2 is VDD, connect it to 5V output of Arduino.

Pin 3 is VEE, for adjusting display contrast. Connect it to the variable terminal of a potentiometer whose fixed terminals are connected to ground and 5V.

Pin 4 is RS (Register Select), it is used to select data or command register. Connect it to pin 12 of Arduino.

Pin 5 is R/W (Read/Write). Connect it to ground since we are only writing data to LCD in this project.

Pin 6 is EN (Enable), it is used to indicate a valid data/command in data lines (D0 ~ D7). Connect it to pin 11 of Arduino.

Pin 7 ~ 10 are data pins (D0 ~ D3), used to transmit data/command to LCD controller. But these pins are not used in 4 bit LCD interfacing, so connect it to ground.

Pin 11 ~ 14 are data pins (D4 ~ D7), used to transmit data/commands to LCD controller. Connect it to Arduino pins 10, 9, 8 and 7 respectively.

CODE

Download DHT Library from here : DHT Sensor Library

.

Open Arduino IDE.

Go to Sketch >> Include Library >> Add .ZIP Library

Select the downloaded ZIP file and press Open.

CODE: https://docs.google.com/document/d/e/2PACX-1vRyvTt081OWuzYB3Vp9N9Hm_7QRWOziohWpCbherxgtZfS_zA8lMv5u5jdudLFwv_zx6wHqDa1v1HFr/pub

WORKING DHT22 sensor is used to read the temperature to control fan speed. It can even read relative humidity also. This sensor is very easy to use and having very good accuracy compared to other sensors. We are using L293D motor driver IC for controlling DC fan/motor with Arduino. It can drive 2 DC motors and we can also control the speed by providing PWM signals. In the program we have set four different conditions to run the DC fan. If the temperature is less than 25°C, then the DC fan will remain off and details will be displayed on the LCD. If the temperature is between 25°C and 30°C, then the DC fan will start working at low speed (30% duty cycle). Similarly if the temperature is between 30°C and 35°C, then the DC fan will run at a medium speed (60% duty cycle). If the temperature is greater than or equal to 35°C, then the DC fan will run at full speed (100% duty cycle).

More in Arduino Boards

You might also need