Make a Shadow sensor circuit using lm 741 IC - KT948

SKU KT948

Power Supply - 9v (from 9v battery) A LM741 is a 8-pinop amp, meaning it has 8 pins all having their different functions. LM 741 IC connected to the Breadboard.

₹750.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES

LM 741 IC – 1

LED - 1

LDR - 2

Transistor BC547 - 1

Resistor 10K- 3, 1K - 2

Capacitor 100nF(104) - 2

Diode 1N4007 - 2

Push Button - 1

Buzzer B-10 - 1

Single Stand Wire 2m - 1

400 pt Breadboard- 1

9v Battery - 1

Battery Snapper - 1

HARDWARE REQUIRED

LM 741 IC – 1

LED - 1

LDR - 2

Transistor BC547 - 1

Resistor 10K- 3, 1K - 2

Capacitor 100nF(104) - 2

Diode 1N4007 - 2

Push Button - 1

Buzzer B-10 - 1

Single Stand Wire 2m - 1

400 pt Breadboard- 1

9v Battery - 1

Battery Snapper - 1

SPECIFICATIONS

Power Supply - 9v (from 9v battery)

PIN DESCRIPTION

LM741 IC

A LM741 is a 8-pinop amp, meaning it has 8 pins all having their different functions. Below is the pinout diagram of a LM741Op amp chip: Pin 1: Offset Null- This is the pin where we add voltage to if we want to eliminate the offset voltage. This is if we want to completely balance the input voltages. More on this at offset termina Pin 2: Inverting Input- This is where the positive part of the input signal that we want to amplify goes if we want our amplified signal inverted. If we don't want it inverted, we place the positive part of the signal into the Non-inverting terminal and place the negative or ground part of our signal here. Pin 3: Non-inverting Input- This is where the positive part of the input signal that we want amplified goes if we want our signal non-inverted. Pin 4: V-- The LM741 Op amp is a dual power supply op amp, meaning it must be supplied positive DC voltage and negative DC voltage. Pin 4 is where the op amp gets supplied with negative DC voltage Pin 5: Offset Null- This is the pin where we add voltage to if we want to eliminate the offset voltage. This is if we want to completely balance the input voltages. More on this at offset terminals Pin 6: Output- This is the terminal where the output, the amplified signal, comes out of. Whatever output the amplifier will drive gets connected to this terminal. Pin 7: V+- This is the terminal which receives the positive DC voltage. Pin 8: NC- This pin stands for Not Connected. It is not used for anything and should be left open.

741 features

large input voltage range

no latch-up

high gain

short-circuit protection

no frequency compensation required

same pin configuration as UA709

741 usage

summing amplifier

voltage follower

integrator

active filter

function generator

BC547 TRANSISTOR

led

Capacitor

Push button

Diode

CIRCUIT DESCRIPTION

Schematic diagram

Connections

LM 741 IC connected to the Breadboard.

Diode 1N4007 positive leg connected to the positive supply and negative leg connected to the Push Button 1st leg.

Push Button 2nd leg to connected Buzzer positive leg and Buzzer negative leg connected to the BC547 Transistor leg 2nd(C-right).

Transistor BC547 Middle leg to connected 1K Resistor and Resistor 2nd leg connected to the LED negative leg , LED positive leg connected to the LM 741 IC Pin No. 6.

Transistor BC547 1st leg(E-left) is GND.

Push Button 2nd leg to connected 100nF(104) capacitor and capacitor 2nd leg is GND.

Push Button 2nd leg to connected LDR 1st leg and LDR 2nd leg connected to the LM 741 IC Pin No. 3 OR Pin No. 3 to connected another LDR leg 1st and LDR 2nd leg is GND.

LM 741 IC Pin No. 4 is GND and Pin No. 2 to connected 10K Resistor and Resistor 2nd leG is GND.

LM 741 IC Pin No. 2 to connected 10K Resistor and Resistor 2nd leg connected to the Pin No. 7 and Pin No. 7 connected to the Push Button 2nd leg.

WORKING

Shadow sensors are widely used to detect the movement of a person in a confined area. Described here is a simple but improved circuit of a smart shadow sensor alarm, which can register a shadow when there is a light difference. Here two 5mm LDRs are used with the popular Op-amp LM741CN to drive an active piezo-sounder when a “valid” shadow is detected. The whole shadow sensor circuit can be powered from four 1.5V AA cells (6VDC), or similar dc supply sources.

Specifications

Power Supply - 9v (from 9v battery)

More in Sensor Modules

You might also need