Make a Radio Car using 434 MHz RF Link Transmitter receiver kit - KT997

SKU KT997

Data rate 200bps to 3Kbps depending on the supply. Remote will be shown like this Connection made as given in picture above for DPDT Switch Connect Pin 1 to 9 and pin 14 to the

₹2098.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

434 MHz RF Link Transmitter receiver kit

Frequency 434 MHz

Transmitter supply voltage: 3~12V.

Receiver Supply voltage: 5V

Receiver IF frequency: 500 kHz

Receiver Sensitivity: -105dBm

Receiver Supply current: 2.3mA

Output power: 4~16dBm

Operating Voltage: 5 Volts

HARDWARE REQUIRED

1x Voltage Regulator 7805

2x 1N4001 Diode

1x HT12E Encoder

1x HT12D Decoder

1 x 434MHz RF Link Transmitter Receiver kit

2x 1K Resistor

2x 3.3K Resistor

2x 47K Resistor

2x 1M Resistor

1X L293D Motor Driver IC

2x Electrolytic Cap 16V 100uF

4x 5mm LED

2x DPDT Rocker switch

1x 9V Battery Clip

1x 9V Battery

1x Plastic Enclosure

1x Robot 3-wheel Chassis kit

1x SPST Rocker Switch

1x Hook-Up Wires AWG22 Solid

1x 12V lithium-ion battery

1x breadboard (400pins)

1Xbreadboard (800 pins)

SPECIFICATIONS

434 Mhz Transmitter Reciever Kit

Frequency 434 MHz

Transmitter: Saw filter based ASK hybrid transmitter

Transmitter supply voltage: 3~12V.R

receiver: ASK superheterodyne receiver with PLL synthesizer and crystal oscillator.

Receiver Supply voltage: 5V

Receiver IF frequency: 500 kHz

Receiver Sensitivity: -105dBm

Receiver Supply current: 2.3mA

Output power: 4~16dBm

Turn on time: 20mS from power is switched on.

Data rate 200bps to 3Kbps depending on the supply.

Operating voltage: 5 Volts

PIN DESCRIPTION

Voltage Regulator 7805

Led

Electrolytic Capacitor

L293DE Motor Driver IC

HT12D Decoder IC

HT12E Encoder IC

434 Mhz Transmitter Receiver Kit

Transmitter PCB Layout

Receiver PCB layout

HOW TO MAKE REMOTE

Cut the Parts as given in picture above:

Remote will be shown like this

Connection made as given in picture above for DPDT Switch

CIRCUIT CONNECTION

Switch Connection

Transmitter (Remote Controller) connection

Connect Pin 1 to 9 and pin 14 to the ground of HT12E IC

Connect pin 16 and 15 via 1M resistor of HT12E IC

Connect Pin 17 of HT12E to data pin of RF link transmitter and pin 18 to the +5v ( Positive rail on breadboard )

Connect pins 10,11,12,13 to the DPDT Rocker switch (s2 and s3 as shown in the photo.

Connect Pin 1 of RF link transmitter to GROUND and pin 3 (VCC) to +5v and connect antenna to pin 4.

Connect the ground pin of 7805 voltage regulator to the ground ,Vin to switch s1 one point and other point to 9v battery then c1(100uf)’s positive Vin and negative to ground and then Vo to Positive rail and c2 capacitor. Positive to Vo and negative to gnd.

1k resistor one terminal to ground and other terminal to negative of led and positive of led to the positive rail.

Receiver (RC car) Connection

Place the decoder IC(HT12D) the motor driver IC and the RF link receiver to the breadboard

Connect the 1 to 9 pins of decoder IC to the ground

Pin ten of ht12d goes to pin 2 of L293d, pin 11 goes to pin 7, pin 12 goes to pin 10 and pin 13 goes to pin 15.

Pin 14 of ht12d goes to pin 2(data) of RF link receiver.

Pin 15 is connected to pin 16 of HT12D via 50k resistor.

Pin 17 is connected to 1k resistor one terminal and other terminal of resistor to the -ve of led and the positive of led to the +5v rail of breadboard.

Pin 18 is also goes to +5v rail.

Pin no. 1,8,9,16 of L293D goes to the +5v rail.

Pin no. 4,5,12,13 to the ground.

Pin 3 and 6 connected to motor m1 and pin no. 11 and 14 to the motor m2.

All three ground pins in the RF link receiver goes to GND rail,vcc1 and vc2 to +5v rail and antenna is connected to

Pin 8(ant).

Now connect one 1N4001 Diode to breadboard connect Positive of diode to the one point of SPST Rocker Switch and other point of

Switch to the 12v li ion battery positive point.

Negative point of diode to the positive rail.

If you want to make this RC car on PCB:

More in Arduino Boards

You might also need