Make a power failure alarm using 555 timer IC and piezo buzzer - KT947

SKU KT947

power Supply - 9v(From 9V battery) The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3

₹825.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

NE555 Timer IC - 1

Transistor BC547 - 3

Diode 1N4007 - 2

LED - 2

Resistor (R1&R2- 100K – 4 pcs , R3 - 1K – 2 pcS,R4 - 10K – 2pc , R5 & R6 - 4.7K – 4 pcs , R7&R8 - 1K – 4 pc

Capacitor (C1 & C2 - 100nF, C3 - 470uF/16V) – 2 pieces each)

Push Button - 2

LDR - 2

Piezo-Speaker - 1

Battery 9v - 1

battery snapper - 1

Jumper Wire ( male to male) – 40 pieces

Single Stand wire 2 meter – 1

Breadboard 840 points - 1

HARDWARE REQUIRED

NE555 Timer IC - 1

Transistor BC547 - 3

Diode 1N4007 - 2

LED - 2

Resistor (R1&R2- 100K – 4 pcs , R3 - 1K – 2 pcS,R4 - 10K – 2pc , R5 & R6 - 4.7K – 4 pcs , R7&R8 - 1K – 4 pc

Capacitor (C1 & C2 - 100nF, C3 - 470uF/16V) – 2 pieces each)

Push Button - 2

LDR - 2

Piezo-Speaker - 1

Battery 9v - 1

battery snapper - 1

Jumper Wire ( male to male) – 40 pieces

Single Stand wire 2 meter – 1

Breadboard 840 points - 1

SPECIFICATIONS power Supply - 9v(From 9V battery) PIN DESCRIPTION

555 Timer IC

Pin

Name

Purpose

1

GND

Ground reference voltage, low level (0 V)

2

TRIG

The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.

3

OUT

This output is driven to approximately 1.7 V below +Vcc, or to GND.

4

RESET

A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.

5

CTRL

Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).

6

THR

The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).

7

DIS

Open collector output which may discharge a capacitor between intervals. In phase with output.

8

Vcc

Positive supply voltage, which is usually between 3 and 15 V depending on the variation.

Led

Capacitor

Diode

CIRCUIT CONNECTION

555 Timer IC connected to the Breadboard and Pin No. 1 is GND.

Pin No. 1 to connected 100nF (104) capacitor and capacitor 2nd leg connected to the Pin No. 2.

Pin No. 3 to connected 1K Resistor and Resistor 2nd leg connected to the BC547 Transistor (T2) Middle leg.

BC547 Transistor (T2) 1st leg (E-right) is GND and 2nd leg connected to the LED negative leg and LED Positive leg connected to the 1K Resistor and Resistor 2nd leg connected to the positive supply.

Push Button 1st led is GND and 2nd leg connected to the positive supply.

BC547 Transistor(T2) 2nd leg to connected Piezo Buzzer negative leg and Buzzer positive leg connected to the Push Button 2nd leg.

470uF capacitor positive leg connected to the positive supply and negative leg is GND.

555 Timer IC Pin No. 4 connected to the BC457 Transistor (T1) 2nd leg(C-left) and Transistor 1st leg (E-right) is GND.

Transistor (T1) Middle leg to connected 1K Resistor and LDR, Resistor 2nd leg is GND and LDR 2nd leg connected to the positive supply.

555 Timer IC Pin No. 5 to connected 100nF (104) capacitor and capacitor 2nd leg connected to the positive supply.

555 Timer IC Pin No. 6 to connected 4.7K resistor and Resistor 2nd led connected Pin No. 7, Pin No. 7 to connected another 4.7K resistor and Resistor 2nd leg connected to the positive supply.

555 Timer IC Pin No. 8 connected to the positive supply.

100K Resistor to connected LED negative leg and LED positive leg to connected diode 1N4007 negative leg.

230v AC connected to the 100K resistor and diode positive leg.

Breadboard connection positive to positive and negative to negative.

WORKING This minuscule power failure alarm circuit is a power supply monitoring device that will set off a piezo-speaker when the ac mains supply cuts off. It is very helpful to indicate the loss of power supply to some power-critical instruments such as a life care device installed in a hospital. Alarm activation at the right time is helpful as it signals that there is a power outage and urgent action should take to recover the situation by providing an alternative power supply.

This is a 9V battery operated, low component count, and light weight circuit which can be safely connected to any AC230V outlet. At its heart is the famed little timer chip LM555 (IC1) configured as an astable multivibrator. Another important component is the “home-baked” opto-coupler (PC1). No bulky power transformer is used here, hence the circuit is “noise-free” (no electromagnetic interference). Although a variety of opto-couplers are available in the market but it may so happen that you may not have one ready at hand when you get a spark and want to check the idea as soon as possible. Fortunately, it is easy to construct one at home using an LED and a phototransistor/photo resistor. Just take a small piece of common circuit board and solder the components as indicated here. Keep an eye on the spacing of the components; it should be as close as possible with a slight gap between them. In the prototype one 5mm white LED + 5mm LDR combination was used. After the construction, enclose the opt coupler in a suitable opaque tube, or cover the whole unit using short-length of heat shrink tube. The circuit is straight forward. As stated, IC1 is here wired as a gated-astable producing an audio-frequency (AF) output (~1 KHz) to drive a standard ordinary/piezo-speaker. Switching of the astable is controlled by the power status detection circuitry built around PC1 and associated components. Switch S1 (SPST) is the system on/off switch, and LED2 (5mm Red) is an optional visual indicator.

Specifications

power Supply - 9v(From 9V battery)

More in Buzzers & Speakers

You might also need

3.5mm TRSS (SMD) Audio Jack PACK OF (4) - RS3666

3.5mm TRSS (SMD) Audio Jack PACK OF (4) - RS3666

This is a 3.5 mm Audio jack Female TRRS SMD. TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards.

₹127.50 GST added at checkout