Make a Pattern with 16 Leds using HC595 shift Register interfacing with Arduino Uno - KT938

SKU KT938

Arduino IDE 1.8.5 (programmable platform for Arduino) Capture and hold data for extended periods of time. Allow simple serial bit streams from a microcontroller to control as many

₹1423.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

Arduino Uno with USB Cable – 1

Breadboard 840 points – 1

Jumper wire (Male to male) – 40pcs

Shift Register(SN74HC595N) – 2

Breadboard 400 points – 1

Single stand wire 2mt- 1

Potentiometer 10 k – 1

Led – 16

Resistor 220 ohm – 16

HARDWARE REQUIRED

Arduino Uno with USB Cable – 1

Breadboard 840 points – 1

Jumper wire (Male to male) – 40pcs

Shift Register(SN74HC595N) – 2

Breadboard 400 points – 1

Single stand wire 2mt- 1

Potentiometer 10 k – 1

Led – 16

Resistor 220 ohm – 16

SOFTWARE REQUIRED Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download :https://www.arduino.cc/en/Main/Software

TYPICAL APPLICATION

HC595 SHIFT REGISTER

General Purpose Logic

Serial to Parallel Data conversion

Capture and hold data for extended periods of time.

Allow simple serial bit streams from a microcontroller to control as many peripheral lines as needed.

Wide array of products such as:

Computer peripheralS

Appliances

Industrial control

SPECIFICATIONS

HC595 SHIFT REGISTER

Wide Supply Voltage Range from 2.0V to 6.0V

Sinks or sources 8mA at VCC = 4.5V

CMOS low power consumption

Schmitt Trigger Action at All Inputs

Inputs accept up to 6.0V

ESD Protection Tested per JESD 22

PIN DESCRIPTION

HC595 SHIFT REGISTER

10K POTENTIOMETER

LED

CIRCUIT DESCRIPTION

Make the circuit (see above) and connect the first shift register as following:

-GND (pin 8) to ground -Vcc (pin 16) to 5V -OE (pin 13) to ground -MR (pin 10) to 5V -DS (pin 14) to Arduino pin 11 -SH_CP (pin 11) to Arduino pin 12 -ST_CP (pin 12) to Arduino pin 8

Connect the second shift register exactly the same, but connect the DS (pin 14) to first register pin 9. After that connect pins: 1, 2, 3, 4, 5, 6, 7 and15 from both registers to LEDs. This connection makes all the pins always active and addressable, however when the Arduino is powered up some of the LEDs may be turned on. Solution for this is to connect MR (pin 10) and OE (pin 13) to Arduino directly, but it this way you have to sacrifice 2 Arduino pins.

To add more shift registers connect them like the second register. Always connect MR and OE pins directly to Arduino and DS pin to previous register

If you want to regulate the brightness of LEDs then connect potentiometer as shown in picture above to control resistance for all LEDs. However it is optional and you can get along without it.

CODE

Click to see the code and copy the link: https://docs.google.com/document/d/e/2PACX-1vSAV7RlsqVdEBp7nkC2yc2gDA_H6_Fra6cPe3fRFmJ-IDiHFyBEOR4Yz9ETlkZ-k1pzg7PyevKDBa6D/pub

WORKING

Connect the Arduino uno and upload the Code given next .After uploading the code you will see the different pattern by glowing led which is controlled by potentiometer.

More in Arduino Boards

You might also need