MAKE A HOME AUTOMATION SYSTEM USING TSOP AND 1 CHANNEL 5V RELAY INTERFACING WITH 4017 IC - KT855

SKU KT855

5 v 1amp adapter – 1 or any 5v Power source The importance Pins look at table below. Pin 16 is positive power supply and pin 8 is a ground.

₹900.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES

TSOP - 1

TV/VCC Remote Control - 1

Transistor BC557 - 1

Capacitor 100uF - 2, 0.1uF(104) - 2

Resistor 220K - 2, 330ohm - 2

LED - 3

1 Channel 5V Relay - 1

5 v 1amp adapter –1

bread board 840 pin -1

single stand wire 2 mt – 1

CD 4017 IC - 1

Jumper Wires male to male– 40 pcs

Jumper Wires male to Female– 40 pcs

HARDWARE REQUIRED

TSOP - 1

TV/VCC Remote Control - 1

Transistor BC557 - 1

Capacitor 100uF - 2, 0.1uF(104) - 2

Resistor 220K - 2, 330ohm - 2

LED - 3

1 Channel 5V Relay - 1

5 v 1amp adapter – 1 or any 5v Power source

bread board 840 pin - 1

single stand wire 2 mt – 1

CD 4017 IC - 1

Jumper Wires male to male– 40 pcs

Jumper Wires male to Female– 40 pcs

SPECIFICATION Power Source: 5v 1amp adapter PIN DESCRIPTION

7 segments Led display

Number of I/O Channels: 1

Type: Digital

Control signal: TTL level

Max. Allowable Voltage: 250VAC/110VDC

Max. Allowable Power Force: From C(800VAC/240W), From A(1200VA/300W)

7 segments Led display

The importance Pins look at table below.

Pin 16 is positive power supply and pin 8 is a ground.

The power supply range of 3 volts to 16 volts and Maximum power supply voltage at pin 1 must not much than 18 volts.

Pin 13 is Clock enabled pins to controls the clock. When it is “0” logic, the clock is enabled and the counter advances one count for each clock pulse.

When “1” logic, the clock input is stop, and the counter does nothing even when clock pulse arrive.

Pin 14 is the clock triggers one count.

The clock pulse must be “clean”. If they are “noisy” the counter may advance two or more times during each clock pulse.

Pin 15 is the reset pin. Normally, it is “0”.

When made “1”, the counter is reset to “0”.

Pins 1-7 and 9-11 are the decoded output pins.

The active count pin goes high and all others remain low.

Pin 12 is Carry output, for the clock input of an additional counter or an external circuit that the count is complete.

7 segments Led display

BC557 Transistor

CIRCUIT CONNECTION

4017 IC Connected to the Breadboard and Pin no. 8, 13 are GND.

4017 IC Pin no. 16 connected to the positive supply and Pin no. 4 & 15 connected to the each other.

4017 IC Pin no. 3 to connected 330 ohm Resistor and resistor 2nd leg to connected LED positive leg and LED negative leg is GND.

4017 IC Pin no. 2 to connected 330 ohm Resistor and resistor 2nd leg to connected LED positive leg and LED negative leg is GND.

4017 IC Pin no. 14 connected to the Transistor 1st leg(E), Transistor 1st leg to connected 220K Resistor and Resistor 2nd leg connected to the positive supply.

Transistor 1st leg(E) to connected 0.1uF capacitor and capacitor 2nd leg is GND and Transistor 3rd leg(C) is GND.

Transistor 2nd leg(B) connected to 3rd Pin of TSOP and TSOP 3rd Pin to connected 100uF capacitor positive leg and capacitor negative leg is GND.

TSOP 1st Pin is GND and 2nd Pin to connected 47ohm Resistor and Resistor 2nd leg connected to the positive supply.

5 volt single channel relay module we connect on bread boardvcc to vcc ,gnd to gnd, input of relay module connect to the 4017 IC PIN NO 2 and we connect no & nc point of relay to ac 220volt.

Breadboard connection positive to positive and negative to negative

WORKING This remote control for home appliances lets you connect your regular everyday appliances to be controlled by a remote. All you have to do is connect this circuit to any of your home appliances (lamp, fan, radio, etc) and you are good to go. The appliance can now be controlled by a remote control working at the designated frequency. The circuit can be activated from up to 10 meters.

Specifications

Power Source5v 1amp adapter

More in Relays

You might also need

12V 7A PCB Mount Relay - SPDT Relay - RS8974

12V 7A PCB Mount Relay - SPDT Relay - RS8974

A 7A 12V DC miniature PCB relay that comes in a baby sugar cube case and is suitable for general applications where high reliability and high switching capacity are needed, but

₹25.50 GST added at checkout