REES52

Make a Gas Level Monitoring System using MQ-2 Gas Sensor Module with NodeMCU ESP8266-12E Board compatible with Arduino Uno Project - KT572

SKU KT572

In this project, we are making an Iot-based gas level Indicator using Node MCU ESP8266-12e wi-fi board and MQ2 gas Sensor by interfacing with Thingspeak.

₹1348.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

INTRODUCTION

In this project, we are making an Iot-based gas level Indicator using Node MCU ESP8266-12e wi-fi board and MQ2 gas Sensor by interfacing with Thingspeak. We will show the measured data on the Thingspeak interface in a graph or a chart.

HARDWARE REQUIRED

Node MCU (esp82 66-12e v1.0) Wi-Fi Board -1pc

NodeMcu USB cable - 1pc

MQ-2 Gas Sensor -1pc

Jumper Wires (male to male) – 20 pcs

830 pt. Breadboard - 1pc

SOFTWARE REQUIRED

Arduino IDE 1.8.10 (programmable platform for Arduino)

Click here to download the software

SPECIFICATIONS

NodeMCU ESP8266 CP2102 Module:

The development board equips the ESP-12E module containing the ESP8266 chip, having a Tensilica Xtensa® 32-bit LX106 RISC microprocessor which operates at 80 to 160 MHz adjustable clock frequency and supports RTOS.

Operating Voltage: 2.5v to 3.6v

On-board 3.3V 600mA regulator

80ma Operating Current

20 µA during Sleep Mode

WARNING

The ESP8266 requires a 3.3v power supply and 3.3v logic levels for communication. The GPIO pins are not 5v-tolerant! You must do some level shifting if you want to interface the board with 5v (or higher) components.

MQ-2 Gas Sensor Module:

Operating Voltage is +5v

Can be used to measure or detect LPG, Alcohol, Propane, Hydrogen, CO and even methane

Analogue output voltage: 0v to 5v

Digital Output Voltage: 0V or 5V (TTL Logic)

Preheat duration: 20 seconds

Can be used as a digital or analogue sensor

The Sensitivity of the digital pin can be varied using the potentiometer

Pin No:

Pin Name:

Description

1

Vcc

This pin powers the module, Typically, the operating voltage is +5v

2

Ground

Used to connect the module to the system ground

3

Digital Out

You can also use this sensor to get a digital output from this pin by setting a threshold value using the potentiometer

4

Analog Out

This pin outputs 0-5V analogue voltage based on the intensity of the gas

LIBRARY REQUIRED

ThingSpeak - Click to open

CIRCUIT CONNECTION

Connect the VCC pin of the MQ-2 Gas Sensor module to the Vin pin of NodeMCU ESP8266-12E Board.

Connect the GND pin of the MQ-2 Gas Sensor module to the GND pin of the NodeMCU pin of the ESP8266-12E Board.

Connect the D0 pin of the MQ-2 Gas Sensor module to the A0 pin of the NodeMCU ESP8266-12E board.

CODE

Click to open in Drive

WORKING AND OUTPUT

Welcome to the IoT-based Gas Detector indicator circuit.

Go to https://thingspeak.com/

Sign up for the account.

After signing up/signing in, go to my channel and create a new channel

Now go to the API keys. Copy your API key and paste it into your Code.

After uploading the code, you will be able to see the readings after measuring the gas level in ppm on the Gas level monitoring system using the Thingspeak IOT platform, in which after several raised values, it will indicate as a graphical point where the Gas Level increases above the set value.

More in WiFi & IoT Modules

You might also need