Make a calculator with the help of 4*4 keypad membrane interfacing with Arduino uno - KT810

SKU KT810

Arduino IDE 1.8.5 (programmable platform for Arduino) Colour tone may slightly change by Temperature and Driving Condition.

₹1125.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT INCLUDES:

4x4 keypad membrane -1

Arduino uno with USB cable - 1

16x2 LCD display -1

Jumper wires ( male to male) – 40 pieces

9V battery with DC Jack - 1

Breadboard 840 points - 1

Single stand wire 2mt- 1

HARDWARE REQUIRED

4x4 keypad membrane -1

Arduino uno with USB cable - 1

16x2 LCD display -1

Jumper wires ( male to male) – 40 pieces

9V battery with DC Jack - 1

Breadboard 840 points - 1

Single stand wire 2mt- 1

SOFTWARE REQUIRED

Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download :https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

4*4 KEYPAD MEMBRANE

Maximum Rating: 24 VDC, 30 mA

Interface: 8-pin access to 4x4 matrix

Operating temperature: 32 to 122 °F(0 to 50°C)

Dimensions: Keypad, 2.7 x 3.0 in (6.9 x 7.6 cm),Cable: 0.78 x 3.5 in (2.0 x 8.8 cm)

16*2 LCD DISPLAY

LCD Display Mode: STN, Positive, Transflective

Display Colour: Deep Blue/ Yellow Green

Viewing Angle: 6H

Driving Method: 1/16 duty, 1/5 bias

Back Light: Yellow-Green LED backlight

Outline Dimension: 803615.8 MAX

Note

Colour tone may slightly change by Temperature and Driving Condition.

The Colour is defined as the inactive/background colour

PIN DESCRIPTION

16*2 LCD DISPLAY

Symbol

External Connection

Function

VSS

Power Supply

Signal GROUND for lcm

VDD

POWER SUPPLY for logic lcm

V0

Contrast Adjust

RS

MPU

Register Select Signal

RW

MPU

Read/Write Select Signal

E

MPU

Operation Enable Signal

DB0~DB3

MPU

Four Low order bidirectional three state bus lines. Used for data transfer between the MPU and LCM. These four are not used between 4 Bit operations.

DB4~DB7

MPU

Four high order bidirectional Three state bus lines used for data transfer between the MPU

A

LED BKL power Supply

Power Supply for BKL

K

4*4 KEYPAD MEMBRANE

Matrix keypads use a combination of four rows and four columns to provide button states to the host device, typically a microcontroller. Underneath each key is a pushbutton, with one end connected to one row, and the other end connected to one column.

CIRCUIT CONNECTION

Keypad 1 to arduino D0

Keypad 2 to D1

Keypad 3 to D2

Keypad 4 to D3

Keypad 5 to D4

Keypad 6 to D5

Keypad 7 to D6

Keypad 8 to D7

Lcd pic 16 to negative rail and pin 15 to positive rail

Lcd pic D7 to D4 to arduino D13 to D10

Arduino 5V to positive rail and ground to negative rail

Arduino pin D8 to RS of lcd and D9 to pin 6 (E) of lcd

Lcd pin1 to ground, pin 2 to 5v , pin 3 to ground and pin 5 to ground

CODE

Programming is always fun and Arduino is a wonderful platform if you are just getting started with Embedded programming. In this, we will build our own calculator with Arduino. The values can be sent in through a keypad (4×4 keypad) and the result can be viewed on an LCD screen (16×2 Dot-matrix). This calculator could perform simple operations like Addition, Subtraction, Multiplication and Division with whole numbers. The complete circuit diagram of this Arduino Calculator Project is given above. The +5V and ground connection shown in the circuit diagram can be obtained from the 5V and ground pin of the Arduino. The Arduino itself can be powered from your laptop or through the DC jack using a 12V adapter or 9V battery. We are operating the LCD in 4-bit mode with Arduino so only the last four data bits of the LCD is connected to Arduino. The Keyboard will have 8 output pins which have to be connected from pin 0 to pin 7 as shown above. You can use the following connection to verify your connection with Arduino, you can also check 4x4 Keypad interfacing with Arduino. "Some Arduino boards might show an error while uploading program if there is anything connected to pin 0 and pin1, so if you experience any just remove the keypad while uploading the program. As told earlier we are going to interface an LCD and keypad with Arduino using libraries. So let’s add them to our Arduino IDE first. The library for LCD is already included in your Arduino by default so we need not worry about it. For Keypad library click on the link to download it from Github. You will get a ZIP file, then add this lib to Arduino by Sketch -> Include Library -> Add.ZIP file and point the location to this downloaded file. Once done we are all set for programming. Even though we have used a library for using a keypad we have to mention few details (shown below) about the keypad to the Arduino. The variable ROWS and COLS will tell how many rows and columns our keypad has and the key map shows the order in which the keys are present on the keyboard

https://docs.google.com/document/d/e/2PACX-1vQIVFRbugqndpyFptAOfi3jq4QcujiIwD4UtCPS06Oz3mtt1HFbl9nZ2B642U1A8jrLpjQMi-OCs0ek/pub

WORKING

Make the connections as per circuit diagram and upload the code below. If it shows error make sure you have added the library as per the instruction is given below

Library Links:

https://www.arduino.cc/en/Reference/LiquidCrystal https://github.com/Chris--A/Keypad

Arduino Calculator using 4x4 Keypad in action

Since the keypad used here does not have proper markings on it I have assumed the Alphabets to be operators as listed below.

Character on Keypad assumed to be “D” Addition (+) “A" Subtraction (-) “B” Multiplication (*) “C” Division (/) “*” Clear (C) “#” Equals (=)

More in Arduino Boards

You might also need