DFRobot

DFRobot Gravity Lab Grade Analog Dissolved Oxygen Sensor/DO Meter Kit For Arduino - Accurate Measurement-RS9814

SKU REES-FC840721C433F8CB

This is a dissolved oxygen sensor kit. A dissolved oxygen meter is used to measure the dissolved oxygen in water, to reflect the water quality.

₹24700.80

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Description:

This is a dissolved oxygen sensor kit. A dissolved oxygen meter is used to measure the dissolved oxygen in water, to reflect the water quality. It is widely applied in many water quality applications, such as aquaculture, environment monitoring, natural science, etc.

There’s an old saying regarding keeping fish, “Good fish deserves good water”. Good water quality is very important to aquatic organisms. Dissolved oxygen is one of the important parameters to reflect water quality. Low dissolved oxygen in the water will lead to difficulty in breathing for aquatic organisms, which may threaten their lives.

The probe is galvanic, does not need polarization time, and stays available at any time. The filling solution and membrane cap are replaceable, leading to a low maintenance cost. The signal converter board is plug-and-play and works from 3.3V - 5V which makes it compatible with most popular microcontrollers such as ESP32, Raspberry Pi, and Arduino.

Specifications:

Dissolved Oxygen Probe

Type: Galvanic Probe

Detection Range: 0~20mg/L

Response Time: Up to 98% full response, within 90 seconds (25℃)

Pressure Range: 0~50PSI

Electrode Service Life: 1 year (normal use)

Maintenance Period: Membrane Cap Replacement Period: 1~2 months (in muddy water); 4~5 months (in clean water) Filling Solution Replacement Period: Once every month

Cable Length: 2 meters

Probe Connector: BNC

Signal Converter Board

Operating Voltage: 3.3~5.5V

Output Signal: 0~3.0V

Cable Connector: BNC

Signal Connector: Gravity Analog Interface (PH2.0-3P)

Dimension: 42mm * 32mm

Features:

Dissolved Oxygen Probe:

Galvanic probe, no need for polarization time

The filling solution and membrane cap are replaceable, low maintenance cost

Signal Converter Board:

3.3~5.5V wide-range power supply, compatible with most Arduino microcontrollers

0~3.0V analog output, compatible with all microcontrollers with ADC function.

Gravity interface, plug, and play, easy to use

Note:

The filling solution is 0.5 mol/L NaOH solution. You need to pour it into the membrane cap before use. Please be cautious with the operation because the solution is corrosive. Please wear gloves! If the solution accidentally drops onto the skin, wash your skin with plenty of water immediately.

The oxygen-permeable membrane in the membrane cap is sensitive and fragile. Be cautious when handling it. Fingernails and other sharp objects should be avoided.

The DO sensor will consume a little oxygen during the measurement. Please gently stir the solution and let the oxygen be distributed evenly in the water.

Projects:

Project 1. Analog Dissolved Oxygen Sensor Tutorial | DIY Arduino D.O. Meter

Introduction: Since measuring the parameter of water quality is a complex task, so measuring the dissolved oxygen in water is also not an easy task. That is why the Dissolved Oxygen Meter (DO Meter) available in the market is very expensive. That is why it is important to make your Dissolved Oxygen Meter. So the Gravity Analog Dissolved Oxygen Sensor from DFRobot is one of the most popular and best Dissolved Oxygen Sensors that are available in the market.

This project will interface a Gravity Analog Dissolved Oxygen Sensor with an Arduino Board and 0.96″ OLED Display. Firstly, preparing the DO Sensor by filling the 0.5N Sodium Hydroxide Solution, then preparing the sensor for testing. Once the sensor is prepared, go through the Arduino Dissolved Oxygen Sensor calibration code & calibrate the sensor. And then finally make your Dissolved Oxygen Meter & display the dissolved Oxygen value in an OLED Display.

Project 2. Build KnowFlow: automatic water monitor

KnowFlow is the name of this water quality monitoring device, based on Arduino Uno. It can automatically monitor 5 parameters of water: pH, Temperature, Dissolved Oxygen, Electronic Conductivity, and ORP.

Project 3. Calibrated Dissolved Oxygen Meter

Introduction: Are you working on an aquaponics or hydroponics project? Or you simply have a fish tank and want your fish to be happy? If yes, you'll probably need a way to measure dissolved Oxygen level.

Useful Links:

Dissolved oxygen sensor Product WIKI

Package Included:

1 x Galvanic Dissolved Oxygen Probe with Membrane Cap

1 x Spare Membrane Cap

1 x Signal Converter Board

1x Gravity Analog Sensor Cable

2 x Waterproof Gasket

1 x Screw Cap for BNC Connector

2 x Plastic Dropper

Dissolved Oxygen Probe:

Galvanic probe, no need for polarization time

The filling solution and membrane cap are replaceable, low maintenance cost

Signal Converter Board:

3.3~5.5V wide-range power supply, compatible with most Arduino microcontrollers

0~3.0V analog output, compatible with all microcontrollers with ADC function.

Gravity interface, plug, and play, easy to use

Specifications

Dissolved Oxygen Probe
TypeGalvanic Probe
Detection Range0~20mg/L
Response TimeUp to 98% full response, within 90 seconds (25℃)
Pressure Range0~50PSI
Electrode Service Life1 year (normal use)
Maintenance PeriodMembrane Cap Replacement Period: 1~2 months (in muddy water); 4~5 months (in clean water) Filling Solution Replacement Period: Once every month
Cable Length2 meters
Probe ConnectorBNC
Signal Converter Board
Operating Voltage3.3~5.5V
Output Signal0~3.0V
Cable ConnectorBNC
Signal ConnectorGravity Analog Interface (PH2.0-3P)
Dimension42mm * 32mm

More in Sensor Modules

You might also need