Control the frequency of Buzzer Module using Push Buttons - KT611

SKU KT611

In this project, we have used buzzer module which will be controlled by the series of Buttons and generate various tones.

₹1348.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Hardware Required

Arduino Uno With USB Cable - 1

Buzzer Module - 1

9v Battery - 1

Snapper With DC Jack - 1

Bread Board 840 Point - 1

Jumper Wire (male to male) - 40 pcs

Single Stand Wire - 1

Push Button - 5

10k ohm Resistance - 6

Introduction In this project, we have used buzzer module which will be controlled by the series of Buttons and generate various tones. HARDWARE REQUIRED

Arduino Uno With USB Cable - 1

Buzzer Module - 1

9v Battery - 1

Snapper With DC Jack - 1

Bread Board 840 Point - 1

Jumper Wire (male to male) - 40 pcs

Single Stand Wire - 1

Push Button - 5

10k ohm Resistance - 6

SOFTWARE REQUIRED Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download:https://www.arduino.cc/en/Main/Software SPECIFICATIONS Buzzer Module Active Buzzer Module produces a single-tone sound when signal is high. To produce different tones use the Passive Buzzer Module. It consists of an active piezoelectric buzzer, it generates a sound of approximately 2.5 kHz when signal is high.

Operating Voltage

3.5V ~ 5.5V

Maximum Current

30mA / 5VDC

Resonance Frequency

2500Hz ± 300Hz

Minimum Sound Output

85Db @ 10cm

Working Temperature

-20°C ~ 70°C [-4°F ~ 158°F]

Storage Temperature

-30°C ~ 105°C [-22°F ~ 221°F]

Dimensions

18.5mm x 15mm [0.728in x 0.591in]

Arduino Uno

CIRCUIT CONNECTION

Attach four buttons on Breadboard.

Connect GND of Arduino Uno with Breadboard for further GND connections.

Connect Pin 5V of Arduino Uno with Breadboard for further 5V power supply connections.

Connect one terminal of Button 1 with Analog Pin A0 of Arduino Uno via 10K Ohm resistor.

Connect one terminal of Button 2 with Analog Pin A0 of Arduino Uno via 10K Ohm resistor.

Connect one terminal of Button 3 with Analog Pin A0 of Arduino Uno via 10K Ohm resistor.

Connect one terminal of Button 4 with Analog Pin A0 of Arduino Uno via 10K Ohm resistor.

Connect other end of all resistors with GND rail of Breadboard.

Connect other terminal of all buttons with 5V rail of Breadboard.

Connect VCC of Buzzer with 5V rail of Breadboard.

Connect GND of Buzzer with GND rail of Breadboard.

Connect Pin Signal of Buzzer with Digital Pin 8 of Arduino Uno.

CODE https://drive.google.com/open?id=1zWxx9yW6HiaNEgqp_LJXE_Rlx4LJD8TM

WORKING Welcome to the Arduino Based Project which consists of Passive Buzzer. The basic working principle of Buzzer is being described here. After uploading the code, when you press the button, Buzzer module generates sound due to the internal oscillation. The buzzer module which will change the frequency of tone from High to Low volume after every button pressed.

More in Arduino Boards

You might also need