Control 2 channel relay module using TTP224B- 4 channel keypad module interfacing with arduino nano - KT923

SKU KT923

In this project we are making a home automation project in which we are using 2 channel relay modules using TTP223B touchpad Module interfacing with Arduino Uno.

₹3000.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

KIT CONTENT

Arduino Nano -1

Nano USB Cable - 1

TTP224b 4- channel capacitive touch module - 1

2 channel relay module - 1

9V battery - 1

Battery snapper - 1

Jumper wire(male to male) - 40 pcs

Jumper wire(male to female)- 40 pieces

Breadboard 830 points - 1

16*2 LCD with i2c module – 1

Introduction In this project we are making a home automation project in which we are using 2 channel relay modules using TTP223B touchpad Module interfacing with Arduino Uno. Here we will press the keys on touchpad to control the Relay 1 and Relay 2. If you are looking for applications like control AC lamp or High voltage DC device you need a relay, so let's do something simple to control 2 channel relay modules. HARDWARE REQUIRED

Arduino Nano -1

Nano USB Cable - 1

TTP224b 4- channel capacitive touch module - 1

2 channel relay module - 1

9V battery - 1

Battery snapper - 1

Jumper wire(male to male) - 40 pcs

Jumper wire(male to female)- 40 pieces

Breadboard 830 points - 1

16*2 LCD with i2c module – 1

SOFTWARE REQUIRED Arduino IDE 1.8.5 (programmable platform for Arduino) Click To Download:https://www.arduino.cc/en/Main/Software

SPECIFICATIONS

TTP224B 4-CHANNEL CAPACITIVE TOUCH MODULE

On-board TTP224 capacitive touch 4 key induction IC

On-board 4 road level indicator.

Working voltage: 2 V to 5.5 V DC

Adjustable output mode, key output mode, longest time and fast/low power output

PCB board size: 35(mm) x29 (mm).

ARDUINO NANO

NANO

Microcontroller

ATmega168

Operating Voltage

3.3V or 5V

Input Voltage

3.35 -12 V (3.3V model) or 5 - 12 V (5V model)

Digital I/O Pins

14 (of which 6 provide PWM output)

Analog Input Pins

8

DC Current per I/O Pin

40 mA

Flash Memory

16 KB (of which 2 KB used by bootloader)

SRAM

1 KB

EEPROM

512 bytes

Clock Speed

8 MHz (3.3V model) or 16 MHz (5V model)

2-channel 5V 10A relay Module This is a 5V, 10A 2-Channel Relay interface board. It can be used to control various appliances, and other equipment’s with large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). It has a 1x4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays. The pins are marked on the PCB:

GND - Connect 0V to this pin.

IN1 - Controls relay 1, active Low! The relay will turn on when this input goes below about 2.0V

IN2 - Controls relay 2, active Low! The relay will turn on when this input goes below about 2.0V

VCC - Connect 5V to this pin. Is used to power the optocouplers

PIN DESCRIPTION

TTP224B 4-CHANNEL CAPACITIVE TOUCH MODULE VCC: 2V to 5.5V DC GND: ground OUT4: high/low output OUT3: high/low output OUT2: high/low output OUT1: high/low output

ARDUINO NANO

RAW

For supplying a raw (regulated) voltage to the board

VCC

The regulated 3.3 or 5 volt supply

GND

Ground pins

RX

Used to receive TTL serial data

TX

Used to transmit TTL serial data

2 and 3

Digital I/O pins. These pins can also be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value

3, 5, 6, 9, 10, and 11

Digital I/O pins. They can also be configured to provide 8-bit PWM output

10, 11, 12 and 13

Digital I/O pins. They can also be configured as SPI pins;

10 - (SS), 11 - (MOSI), 12 - (MISO) and 13 - (SCK)

A0 to A3

Analog input pins

A4 and A5.

Analog input pins. They can also be used as IIC pins;

A4 - (SDA) and A5 – (SCL).

A6 and A7

Analog input pins

Reset

The microcontroller can be reset by bringing this pin low

2 channel 5v 10A relay Module

COM- Common pin

NC- Normally Closed, in which case NC is connected with COM when INT1 is set low and disconnected when INT1 is high;

NO- Normally Open, in which case NO is disconnected with COM1 when INT1 is set low and connected when INT1 is high.

Terminal 2 is similar to terminal 1, except that the control port is INT2

INT 1- Relay 1 control port

INT 2- Relay 2 control port

CIRCUIT CONNECTION Connections are as follows :

Out1 of TTP224 to the Nano D11

Out2 of TTP224 to the Nano D10

Out3 of TTP224 to the Nano D9

Out4 of TTP224 to the Nano D8

Ground to the negative rail and Vcc to the positive rail

I2C module Vcc to positive rail and ground to the negative rail

I2C module SDA pin to Nano A4 and SCL to A5 Nano

Nano 5v pin to the positive rail

IN1 of relay module goes to D4

IN2 of relay module goes to D5

Vcc of relay module to positive rail and ground to the negative rail

CODE Click to see the code or copy the link: https://drive.google.com/open?id=1zgu_BTbgCzaSqHQe0o0rDVSx10Y3XdPv

WORKING Upload the code and see the output. If you are looking for applications like control AC lamp or High voltage DC device you need a relay, so let's do something simple to control Relay 2 channel Touch Pad 1 and 2 to control Relay #1 Touch Pad 3 and 4 to control Relay #2

More in Arduino Boards

You might also need