Blink a Led using Hand’s clap - KT903

SKU KT903

The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open).

₹748.50

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

BC547 Transistor – 2

100NF Capacitor -3

100uF Capacitor -2

1K Resistor-2

6.7K Resistor-2

47K Resistor-2

330 Ohm Resistor - 2

470 Ohm Resistor - 2

NE555 Chip - 1

LED(Light Emitting Diode) blue- 2

Single stand wire 2m - 1

Breadboard 840 points - 1

9V Battery with snapper – 1

Condenser Mic - 1

HARDWARE REQUIRED

BC547 Transistor – 2

100NF Capacitor -3

100uF Capacitor -2

1K Resistor-2

6.7K Resistor-2

47K Resistor-2

330 Ohm Resistor - 2

470 Ohm Resistor - 2

NE555 Chip - 1

LED(Light Emitting Diode) blue- 2

Single stand wire 2m - 1

Breadboard 840 points - 1

9V Battery with snapper – 1

Condenser Mic - 1

PIN DESCRIPTION

2 Colour Led module

2 Colour Led module

Pin

Name

Purpose

1

GND

Ground reference voltage, low level (0 V)

2

TRIG

The OUT pin goes high and a timing interval starts when this input falls below 1/2 of CTRL voltage (which is typically 1/3 Vcc, CTRL being 2/3 Vcc by default if CTRL is left open). In other words, OUT is high as long as the trigger low. Output of the timer totally depends upon the amplitude of the external trigger voltage applied to this pin.

3

OUT

This output is driven to approximately 1.7 V below +Vcc, or to GND.

4

RESET

A timing interval may be reset by driving this input to GND, but the timing does not begin again until RESET rises above approximately 0.7 volts. Overrides TRIG which overrides threshold.

5

CTRL

Provides “control” access to the internal voltage divider (by default, 2/3 Vcc).

6

THR

The timing (OUT high) interval ends when the voltage at threshold is greater than that at CTRL (2/3 Vcc if CTRL is open).

7

DIS

Open collector output which may discharge a capacitor between intervals. In phase with output.

8

Vcc

Positive supply voltage, which is usually between 3 and 15 V depending on the variation.

Led

CIRCUIT DIAGRAM

connect emitter of two BC547 TRANSISTOR to the negative rail of BREADBOARD

connect the 6.7K RESISTOR from base of 1st BC547 to NEGATIVE rail

connect the 1k Resistor from the collector of 1st BC547 to POSITIVE rail

connect the collector of 1st bc547 to the base of 2nd bc547

connect the 470 ohm resistor from the collector of the second bc547 to the POSITIVE rail

connect pin 4 & 8 of 555ic to POSITIVE rail

connect pin 6 of the 555ic to pin 7 of 555ic

connect the 47k resistor from pin 6/ 7 of 555ic to the POSITIVE rail

connect the NEGATIVE terminal of 100uf cap to NEGATIVE rail

insert the other 0.1 uf cap on the breadboard with one terminal with pin 2 of 555ic

insert the LED anode via 330 ohm resistor to pin 3 of 555ic and cathode with -ve rail

insert the condenser POSITIVE to POSITIVE rail and NEGATIVE to base of 1st bc547

connect the 9v battery to the breadboard.

OUTPUT Whenever you clap by your hands, led will start blink. *The glow time of led depend on the value of the capacitor if value is high then glow time will high and vice versa

More in LEDs & Lighting

You might also need