Arduino Mega Pololu Compatible Shield RAMPS 1.4 for 3d printer, Prusa Mendel - RS1063

SKU RS1063

Fused at 5A for additional safety and component protection Heated bed control with additional 11A fuse I2C and SPI pins left available for future expansion.

₹360.00

18% GST added at checkout

In stock

₹150 flat shipping, free over ₹3000

  • Pay by UPI: GPay, PhonePe, Paytm & BHIM (no gateway fees)
  • GST invoice on every order
  • Payment confirmed by us before dispatch (no auto-charge)
  • Dispatched in 2–4 working days from Agra, Uttar Pradesh.

Buying for a school or in bulk? Ask us for institutional pricing. Get a quote

About this product

Supply Voltage: 12 V

Fused at 5A for additional safety and component protection

Heated bed control with additional 11A fuse

I2C and SPI pins left available for future expansion.

2 stepper motor for Z axis in parallel

Description: This RAMPS stands for Rep Rap Arduino-compatible MEGA Pololu Shield. It is built for combining all electronic components needed for your Rep Rap 3D printer on one shield. This means that you can control up to 5 stepper motors, 3 temperature sensors, 6 end switches, 1 heat bed, 1 fan and 1 extruder with this shield. Connection possibility for 5 stepper motors, 3 temperature sensors, 6 end switches, 1 heat bed, 1 fan and 1 extruder. For use with Arduino Mega 1280 and Arduino Mega 2560. Specification:

Supply Voltage: 12V

Fused at 5A for additional safety and component protection

Heated bed control with additional 11A fuse

Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.

I2C and SPI pins are left available for future expansion.

2 stepper motor for Z axis in parallel

Features:

Standard interfaces (as that of the extruder)

Reserved GCI like I2C and RS232

MOSFET 3 MOSFET is applied to the heater/ fan and thermistor circuit.

Another 5A was added to protect the component parts.

An 11A fuse is added to the hotbed.

Support 5 stepper drive board

The adoption of Pin Header as Pololu makes it more convenient to repair or change.

I2C and SPI are reserved for expanding

All the MOSFET can be controlled by PWM

Use the interface of the servo motor to adjust the level of the printing platform automatically.

Adding an SD module for the SD ramps module.

LED can indicate the status of the heater (the opening and close of MOS).

Expandable to control other accessories.

Caution:

Please read the technical parameters of the board carefully before you use it;

Only connect the mega2560 board with the computer via the USB cable while programming firmware;

Reversed connection of the power supply or the motor driver may cause the board to burn, please confirm again before power is on;

Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board;

Select the appropriate load according to the board voltage/current requirement, if the work current exceeds the load of the board it may cause the board to burn.

Software:

Compiling environment: Arduino IDE

Firmware: Marlin

PC software: Print run, Repetier-Host

Package Included: 1 x Arduino Mega Pololu Compatible Shield RAMPS 1.4 for 3d printer, Prusa Mendel

Standard interfaces (as that of the extruder)

Reserved GCI like I2C and RS232

MOSFET 3 MOSFET is applied to the heater/ fan and thermistor circuit.

Another 5A was added to protect the component parts.

An 11A fuse is added to the hotbed.

Support 5 stepper drive board

The adoption of Pin Header as Pololu makes it more convenient to repair or change.

I2C and SPI are reserved for expanding

All the MOSFET can be controlled by PWM

Use the interface of the servo motor to adjust the level of the printing platform automatically.

Adding an SD module for the SD ramps module.

LED can indicate the status of the heater (the opening and close of MOS).

Expandable to control other accessories.

Specifications

Supply Voltage12V
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins are left available for future expansion.
2 stepper motor for Z axis in parallel

More in Arduino Shields

You might also need